JVC HR-J465EK Screen, Access Mode SET, Select Picture Control SET Mode, Adjust Tracking, Manually

Page 24

24ADVANCEDOPERATIONS(cont.)

Playback Pic- ture Adjustment

Picture Control

This feature helps you to adjust the playback picture quality according to your preference. *The default setting is "AUTO."

ACCESS MAIN MENU

SCREEN

1

MENU

0

?

3

4

TV PROG

OK

1 Press MENU.

 

 

ACCESS MODE SET

 

SCREEN

 

 

Move the highlighted bar (pointer) to "MODE SET" by

2 pressing , then press OK or #.

 

 

SELECT PICTURE

 

3

CONTROL SET MODE

Move the highlighted bar

MODE SET

(pointer) to "PICTURE

ON

B. E. S. T.

Manual Tracking

Your video recorder is equipped with automatic tracking control. For most tapes this will automatically adjust the tracking to suit the particular tape you are playing. In some circumstances it may be necessary to make manual tracking adjustments. This is usually only associated with old or worn tapes or recordings made on old or worn recorders. If the automatic tracking control fails to operate correctly you will see noise bars across the picture as shown on the left below. To correct this you can override the automatic control and adjust the tracking manually by pressing the TV PROG buttons.

OVERRIDE AUTOMATIC TRACKING

1

Press

on the remote to engage manual tracking.

 

ADJUST TRACKING

2

MANUALLY

Press TV PROG + or to adjust tracking.

 

RETURN TO AUTOMATIC

 

TRACKING

 

Press

on the remote to re-engage automatic

3 tracking.

 

NOTE:

CONTROL" by pressing

 

 

PICTURE CONTROL

AUTO

, then press OK or #to

AUTO TIMER

OFF

select the desired mode.

O. S. D.

ON

AUTO: Provides optimised

AUTO SP=LP TIMER

OFF

 

 

 

picture benefits of

 

 

 

B.E.S.T. Picture

[] =

 

 

System. Normally

[MENU] : EXIT

 

 

select AUTO.

 

 

EDIT:

Minimizes picture degradation during editing

 

(recording and playback).

 

SOFT:

Reduces image coarseness when viewing

 

 

overplayed tapes containing a lot of noise.

 

SHARP: Clearer, sharper-edged picture when viewing

 

images with lots of flat, same-coloured surfaces

 

such as cartoons.

 

 

NOTES:

When you select EDIT, SHARP or SOFT, the selected mode will not change until you select again.

When you select EDIT to dub tapes, be sure to select AUTO after you finish dubbing the tapes.

RETURN TO NORMAL

SCREEN

4 Press MENU.

NOTES:

When B.E.S.T. is OFF, "PICTURE CONTROL" switches automatically from AUTO to NORM.

Select EDIT when you are dubbing tapes. Refer to page 22.

When a new tape is inserted, the recorder returns to the automatic tracking mode automatically.

Image 24
Contents HR-J465EK HR-J265EK HR-J260EK HR-J265ES Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Back of RecorderMains outlet Before performing the following procedure, make sure that Your TV via both an RF cable and a 21-pinGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackActivate HIGH-SPEED Search PlaybackActivate SLOW-MOTION Playback Recording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingSatellite Receiver Users Press SP/LPExpress Timer Programming Enter ProgrammeStart Time Enter Programme Stop TimeSET PDC Mode Press TV Prog +/- toCheck, Cancel And Replace Programmes Looking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Aerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitPress SP/LP on the remote control to set the tape speed Before performing the following stepsSET Recording DECK’S Input Mode SET Edit ModeEdit To Or From Another Video Recorder Make ConnectionsEdit From a Camcorder ModeStart Camcorder Start RecorderAccess Mode SET Select Picture Control SET ModeAdjust Tracking ScreenAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsSelect Mode Auto SP→LP TimerAuto Timer Activate Repeat Repeat PlaybackNtsc Playback Next Function MemoryAccess Video CHAN- NEL SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelAccess Video Chan NEL SET Mode With RF ConnectionAccess Main Menu Tuner SetPerform Auto Chan NEL SETScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Access Manual Channel SET Screen Switch StationsSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup Access Initial SET ScreenAccess Guide Prog SET Screen Enter Guide Prog NumberQuestions And Answers Remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Re-perform the clock and/or timer settings Camcorder recording is not possibleIndex Front ViewAV2 IN/DECODER Connector enables connection Symbolic Mode IndicatorsProgramme Time Indicators show the programme Tape Remaining Time Indicator displays time remainingRemote Control Auto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingMemo Memo DA4 Double Azimuth helical Rotary two-head herical scanIN/OUT x 1, IN/DECODER x VHF 44.5 143/143 470 MHz