JVC HR-S5700AM System Setup, Access G-CODE Showview Setup Screen, Number, EN Timer Recording

Page 24

24ENTIMERRECORDING

G-CODE™/SHOWVIEW™

System Setup

Turn on the TV and select the VIDEO channel (or AV mode).

The G-CODEtimer programming system eliminates the need to input channel, date, start and stop time data when setting the timer record function. Simply key in the G-CODEnumber for the TV programme you wish to record (found in most TV listings) and the recorder's timer is automatically programmed.

You have to set "GUIDE PROG" numbers, which are assigned to each station for purposes of G-CODEtimer programming, for all the stations stored in your recorder's memory to get proper results.

Before G-CODEsystem setup you must have performed the following procedures:

●Tuner setting ( pg. 8, 46)

●Clock setting ( pg. 12)

INFORMATION

G-CODEand SHOWVIEW are different trademarks used to represent the same easy recording feature, but only the term G-CODEsystem will be used in the instructions. If you use the SHOWVIEW system, follow the same instructions listed for the G-CODEsystem.

1	2	3	NUMBER
		2	NUMBER
4	5	6

7 8 9

4

0

1

OK

MENU

PUSH JOG

IMPORTANT

Perform the following procedure after Auto Set Up on page 8 and/or the channel setting steps on pages 46– 49.

After setting the Guide Program Numbers, channel positions may be incorrect if you stored or skipped channels. In this case, re-perform Guide Program Number setting.

Guide Program Number Set

		ACCESS MAIN MENU
1		SCREEN
1		Press MENU.
		ACCESS INITIAL SET
2		SCREEN
		Press PUSH JOG %ﬁ to place the pointer next to
		"INITIAL SET", then press OK or PUSH JOG %.
		ACCESS G-CODE/
		SHOWVIEW SETUP
3		SCREEN
		Press PUSH JOG %ﬁ to place the pointer next to
		"G-CODE/SHOWVIEW SETUP", then press OK or
		PUSH JOG %.

		ENTER GUIDE PROG
4		NUMBER
		Press PUSH JOG %ﬁ or	G-CODE/SHOWVIEW SETUP
		NUMBER keys to enter the	G-CODE/SHOWVIEW SETUP
		NUMBER keys to enter the
		Guide Program number for	GUIDE PROG	TV PROG
		the desired station as shown	2	5
		in the TV listings. Then %	2	5
		press OK or PUSH JOG .	[0-9] OR [5/∞]:SELECT =
			[0-9] OR [5/∞]:SELECT =
			[MENU] : EXIT

Image 24

Contents HR-S5700AM Safety Precautions Moisture Condensation Check Contents Basic ConnectionsSituate Recorder MainsVideo Connection Connect Recorder to TVConnect Recorder to Mains Back of RecorderAccess Video Channel SET Mode Video Channel SetEN Initial Sett Ings With RF ConnectionSET Video Channel Finish Video Channel SETFinish Video Channel SETAuto Set Up Select LanguageSET Time SET DateDuring Auto Set Up Select TV SystemStart Auto Channel SET Major Countries TV SystemAccess Main Menu Screen ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Turn on the RecorderAccess Initial SET Screen Select LanguageAccess Clock SET Screen Clock SetStart Clock Operation Press Push JOG %ﬁ to set the yearBasic Playback Load a CassettePoint Start PlaybackPlayback Features Activate HIGH-SPEED SearchHigh-Speed Search Slow MotionAdjust Tracking Manually Activate Index SearchOverride Automatic Tracking Return to Automatic TrackingSkip Over Unwanted SectionsActivate Instant Review Basic Recording Recording Features Select Channel to WatchSET Counter Display EN RecordingEngage ITR Mode SET Recording DurationDisplay Remaining Time Access Function SET Screen Select S-VHS ModeVHS Super VHS, S-VHS ET and VHS Select S-VHS ET SET ModeSuper VHS ET Access Main Menu Screen S.T. Picture SystemReturn to Normal Screen PreparationRecording PlaybackOr press Record on the recorder During B.E.S.TSystem Setup Access G-CODE Showview Setup ScreenEN Timer Recording NumberEnter Receiving Channel Position Number Number keys to inputNumber of the recorders Received. Then press OKTimer Programming Access G-CODE Showview ScreenAccess G-CODE Programme Screen Enter G-CODE NumberTimer Mode Return to NormalEngage Recorders Express Timer Programming Start TimeOr OK. Program Completed appears on Screen for about 5 seconds, then normal screenRepeat steps 1 8 for each additional programme Disengage Timer Mode Cancel or Replace a ProgrammeReturn to Timer Mode Check, Cancel And Replace ProgrammesCancel or Change Programme SettingConfirm the Overlap Ping ProgrammesAccess Function SET Timer RecordingAuto Timer Auto SP LP TimerAutomatic Sat- ellite Program Recording Before performing the following stepsRemote Control Functions Remove Power SupplySET Remote Control Code RE-SUPPLY PowerTV Multi-brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code Operate TVMulti-brand Remote Control SET Brand CodeOperate Unit TV PR +/-,NUMBER keysCable Box or Satellite Re- ceiver Multi-brand Code DVD Multi-brand CodeCable BOX Brand Name Code DVD Brand Name CodeConnecting Using a Stereo System Make ConnectionsAUX in or Tape Monitor Speaker Audio Cable not provided Speaker Mains outletAccess Main Nenu Screen SET ModePreparation For Editing EditingControl SET Mode If the camcorder has no S-VIDEO output connector RecorderIf the camcorder has an S-VIDEO output connector Recorder Edit From CamcorderSET Recording Decks Input Mode Edit To Or From Another Video RecorderStart Source Player Start Recording DeckSET Input Mode Audio DubbingLocate Start Point Engage Audio DubbingStart Dubbing END Audio DubbingSetting Of The Colour System Select Buttons Off-Air RecordingTape-To-Tape Editing Playback equipmentDubbed tape Access Main Menu Access Tuner SETSelect Auto CH SET Tuner SETAccess Channel List Select TV SystemSelect Position SET Desired StationAccess Channel List EN Tuner SETDelete a Channel Swap Channel PositionsFine-Tuning Channels FINE-TUNETroubleshooting If youre using the RF OUT connec- tionPress Play to turn the indicator off Check the cassette Recording TR Oubleshooting New one. pgQuestions and Answers Playback Timer RecordingIndex @S-VHS ET Button pgDUB Audio Dubbing Button pg 3AUDIO/VIDEO OUT Connectors pg , 5 Rear ViewTV PR +/- Button pg CABLE/SAT/DVD Button pgEWEEKLY Button pg UPR +/- Button pgSpecification S Supplied fresh battery actualMaximum recording time Memo Memo HR-S5700AM