JVC LPT0428-001A, HR-S5700AM Select TV System, Start Auto Channel SET, Major Countries TV System

Page 9

Major Countries

TV System

 

 

Australia, New Zealand, Kuwait, U.A.E.,

 

Indonesia, Singapore, Thailand, Malaysia,

B/G

Iran, Saudi Arabia, Egypt, Morocco,

 

Lebanon, Iraq

 

 

 

China, Mongolia, Russia

D/K

 

 

Hong Kong

I

 

 

U.S.A., Japan, S.Korea, Taiwan

M

 

 

0

1

OK

PUSH JOG

5

6

EN9

SELECT TV SYSTEM

Press PUSH JOG %fi to place the pointer next to the appropriate TV system (refer to the table on the left).

START AUTO CHANNEL SET

Press OK or PUSH JOG .

The Auto Set Up function scans all the channels that are receivable by your recorder. It then automatically assigns each receivable channels to the PR +/– buttons. It skips non-receivable channels.

As Auto Set Up progresses, the " " mark on the

screen moves from left to right. (See below.)

DO NOT press any button on the recorder or remote control while Auto Set Up is in progress.

AUTO CH SET

PLEASE WAIT

STARTFINISH

During Auto Set Up

"PLEASE WAIT" blinks on the screen and "Auto" blinks on the front display panel.

TV Screen

When Auto Set Up is completed, the lowest position number will appear on the front display panel.

NOTES:

If you perform Auto Set Up when the aerial cable is not connected properly, "SCAN COMPLETED -NO SIGNAL-" appears on the screen. When this happens, make sure of the aerial connection and press OK; Auto Set Up will take place again.

If there is a power cut, or if you press or MENU while Auto Set Up is in progress, Auto Set Up will be interrupted; be sure to turn off the recorder power once and try again.

If you want to set the tuner manually such as to add or skip channels, to swap channel positions, or to fine-tune channels,  pg. 47 – 49.

If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels.  "TV System Selection – When you see the picture but the audio can't be heard or sounds unnatural" on page 49.

Image 9
Contents HR-S5700AM Safety Precautions Moisture Condensation Basic Connections Check ContentsSituate Recorder MainsConnect Recorder to TV Video ConnectionConnect Recorder to Mains Back of RecorderVideo Channel Set Access Video Channel SET ModeEN Initial Sett Ings With RF ConnectionFinish Video Channel SET SET Video ChannelFinish Video Channel SETSelect Language Auto Set UpSET Time SET DateSelect TV System During Auto Set UpStart Auto Channel SET Major Countries TV SystemENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenOn-Screen Displays Turn on the RecorderSelect Language Access Initial SET ScreenClock Set Access Clock SET ScreenStart Clock Operation Press Push JOG %fi to set the yearLoad a Cassette Basic PlaybackPoint Start PlaybackActivate HIGH-SPEED Search Playback FeaturesHigh-Speed Search Slow MotionActivate Index Search Adjust Tracking ManuallyOverride Automatic Tracking Return to Automatic TrackingSkip Over Unwanted SectionsActivate Instant Review Basic Recording Select Channel to Watch Recording FeaturesSET Counter Display EN RecordingEngage ITR Mode SET Recording DurationDisplay Remaining Time Access Function SET Screen Select S-VHS ModeVHS Super VHS, S-VHS ET and VHS Select S-VHS ET SET ModeSuper VHS ET S.T. Picture System Access Main Menu ScreenReturn to Normal Screen PreparationPlayback RecordingOr press Record on the recorder During B.E.S.TAccess G-CODE Showview Setup Screen System SetupEN Timer Recording NumberNumber keys to input Enter Receiving Channel Position NumberNumber of the recorders Received. Then press OKAccess G-CODE Showview Screen Timer ProgrammingAccess G-CODE Programme Screen Enter G-CODE NumberTimer Mode Return to NormalEngage Recorders Start Time Express Timer ProgrammingOr OK. Program Completed appears on Screen for about 5 seconds, then normal screenRepeat steps 1 8 for each additional programme Cancel or Replace a Programme Disengage Timer ModeReturn to Timer Mode Check, Cancel And Replace ProgrammesProgramme Setting Cancel or ChangeConfirm the Overlap Ping ProgrammesTimer Recording Access Function SETAuto Timer Auto SP LP TimerBefore performing the following steps Automatic Sat- ellite Program RecordingRemove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVSET Brand Code Multi-brand Remote ControlOperate Unit TV PR +/-,NUMBER keysDVD Multi-brand Code Cable Box or Satellite Re- ceiver Multi-brand CodeCable BOX Brand Name Code DVD Brand Name CodeMake Connections Connecting Using a Stereo SystemAUX in or Tape Monitor Speaker Audio Cable not provided Speaker Mains outletSET Mode Access Main Nenu ScreenPreparation For Editing EditingIf the camcorder has no S-VIDEO output connector Recorder Control SET ModeIf the camcorder has an S-VIDEO output connector Recorder Edit From CamcorderEdit To Or From Another Video Recorder SET Recording Decks Input ModeStart Source Player Start Recording DeckAudio Dubbing SET Input ModeLocate Start Point Engage Audio DubbingEND Audio Dubbing Start DubbingOff-Air Recording Setting Of The Colour System Select ButtonsTape-To-Tape Editing Playback equipmentDubbed tape Access Tuner SET Access Main MenuSelect Auto CH SET Tuner SETSelect TV System Access Channel ListSelect Position SET Desired StationEN Tuner SET Access Channel ListDelete a Channel Swap Channel PositionsFINE-TUNE Fine-Tuning ChannelsTroubleshooting If youre using the RF OUT connec- tionPress Play to turn the indicator off Check the cassette Recording New one.  pg TR OubleshootingPlayback Timer Recording Questions and AnswersIndex @S-VHS ET Button  pgDUB Audio Dubbing Button  pg Rear View 3AUDIO/VIDEO OUT Connectors  pg , 5CABLE/SAT/DVD Button  pg TV PR +/- Button  pgEWEEKLY Button  pg UPR +/- Button  pgSpecification S Supplied fresh battery actualMaximum recording time Memo Memo HR-S5700AM