JVC HR-S7722EK, HR-S7700EK setup guide Timer Warning, PDC Recording

Page 19

 

SET TAPE SPEED

4 Press SP/LP (

) to set the tape speed.

5

SET PDC MODE

Press PDC to select "ON" or "OFF".

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, PDC is set to ON.

 

If "VPS/PDC OFF" is displayed on the screen or "VPS/

 

PDC" is not lit on the display panel, PDC is set to OFF.

 

☞ "PDC Recording" in the column below.

 

● VPS (Video Programme System) recording is not

 

currently available in the U.K. and not possible with

 

this recorder.

 

 

RETURN TO NORMAL SCREEN

 

Press PROG or OK. "PROGRAM COMPLETED" appears

 

on the screen for about 5 seconds, then normal screen

6 appears. If the timer programme is overlapped with

 

another one that was already set, "PROGRAM

 

OVERLAPPED" appears on screen and "Err" appears on

19

Satellite Receiver Users

To timer-record a satellite broadcast using the VIDEO Plus+ system:

1 Perform "Satellite Receiver Control Setting" (☞ pg. 12). 2 Perform steps 1 – 7. In step 3, the display panel shows "L2" for the preset position. In step 5, you cannot set

PDC to ON.

3 Leave the satellite receiver's power on.

ATTENTION

Regarding Guide Program Number Set

"GUIDE PROG SET" appears after performing step 3 if the Guide Program number for the PlusCode number you entered has not been set.

● If you want to set the Guide Program number for the satellite broadcast station, press the NUMBER key "0" to change "TV PROG" to "SAT". Press %Þ to input the preset position number on which your recorder or satellite receiver receives that station, then press OK or # to set the Guide Program Number. The VIDEO Plus+ Program screen appears.

 

the front display panel. (☞ pg. 23)

 

 

 

● Repeat steps 1 – 6 for each additional programme.

 

 

 

ENGAGE RECORDER’S TIMER

7

MODE

Press ä (TIMER). The recorder turns off automatically

and ä appears on the display panel.

 

● To disengage the timer, press ä (TIMER) again.

GUIDE PROG SET

GUIDE PROG

TV PROG

2

– –

[5°] =

[0]:SAT

[PROG] : EXIT

 

(Ex.) To timer-record a BBC2 programme with the VIDEO Plus+ system.

*If your recorder receives BBC2 on the preset position 2, press OK or #after entering "2" using %Þ buttons.

NOTES:

● To Change The Stop Time . . .

. . . press STOP +/– after pressing OK in step 3. You can

compensate for anticipated programme schedule delays this

way.

● To Timer-Record Weekly Or Daily Serials . . .

. . . after pressing OK in step 3, press WEEKLY (NUMBER key

“9”) for weekly serials or DAILY (NUMBER key “8”) for daily

serials (Monday – Friday). Either "WEEKLY" or "DAILY"

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes.

–WARNING– TIMER RECORDING

TO START SOON

[]

appears on the screen. Pressing the button again makes the

corresponding indication disappear.

● You can programme this recorder to timer-record as many as 8

programmes. If you try to programme the recorder to record a

ninth, "PROGRAM FULL" appears on screen and "FULL"

appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes (☞ pg. 22).

● It is not possible to timer-record a TV programme with a

PlusCode number which starts with "0".

NOTES:

●The warning only appears if you’re not in the Timer mode at the time.

●If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service in some areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel (☞ step 5 above).

NOTES:

●PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 (L-2) IN/DECODER on your recorder.

●PDC recording is also possible via the AV1 (L-1) IN/OUT connector.

Page 18 Page 20
Image 19
Page 18 Page 20
Contents HR-S7700EK HR-S7722EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV To connect to a TV with 21-pin AV input connector ScartBack of Recorder Video Connection Mains outlet Mains Power CordTion pg and the TV is turned on, Before performing the following procedure, make sure thatAuto for Auto Set Up function Refer to With the AV or S-VIDEO connectionYou will need to start again. See Notes below Or remote control until the display panelShows either the display as illustrated on Progress, this process will be interruptedIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notNexTView Link TV Auto Power OnLink Functions Turn on the RecorderSatellite Receiver Control Setting Channel position Select Satellite RECEIVER’S Channel for TestingEnter Satellite RECEIVER’S Brand Check Result of TestStart Playback PlaybackLoad a Cassette Find Programme Start PointActivate HIGH-SPEED Search Pause During Playback Recording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeEnter Pluscode Number Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Access Video PLUS+ Program ScreenPDC Recording Timer WarningEnter Programme Date Express Timer ProgrammingBefore performing Express Timer Programming TimeEngage RECORDER’S SET PDC ModeTimer Mode Return to NormalReturn to Timer Mode Check, Cancel And Replace ProgrammesAccess Programme SCREEN/ Display Cancel or Replace a ProgrammeConfirm Overlapping Programmes When programmes overlap each otherCancel or Change Programme Setting To cancel a programmeDigital 3R Playback Picture AdjustmentDigital TBC/NR Manual TrackingDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionSkip Over Unwanted Looking For Scene You WantActivate Index Search Activate Instant ReviewSuper VHS S-VHS VHS ET and VHS Recording According To Tape TypeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsPlayback RecordingOr press Record on the recorder Aerial Connector TV Aerial cable Audio in connectorAutomatic Satellite Programme Recording Satellite Receiver UnitEngage Auto Satellite Prog Select L-2 Select ModeREC Mode ScreenMinimizing Picture Degradation While Editing Access Main Menu ScreenAccess Mode SET Screen Select Picture Control SET ModeStart Camcorder SET RECORDER’S Input ModeSET Edit Mode Make ConnectionsSET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderRecorder Player SELECT/INPUT Setting OUTPUT/INPUT SettingStart Dubbing SET Input ModeLocate Start Point Engage Audio DubbingInsert Editing Reset the CounterLocate END Point Start Editing Engage Insert EditingEND Insert Editing Other Functions ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Display Auto Timer Power Save ModeNext Function Memory Then press OK or #to select Auto SP→LP TimerFor Example SET, then press OK or #Ntsc Playback Engage RECORD-PAUSE ModeResume Recording Repeat PlaybackSpeaker Television Mains outlet Connection To Stereo SystemNumber Video Plus+ SetupGuide Program Number Set SET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Perform Auto Channel SET Tuner SetAuto Channel Set Is displayed on the screen Screen preset positionsProcedures After Scan CompletedEnter NEW Channel Information Storing Channels ManuallySelect Band Input ChannelDelete a Channel When Receiving a Scrambled BroadcastChange Station Preset Position Fine-Tuning Channels Already StoredSelect NEW Station Access ManualSwitch Stations Channel SET ScreenTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetÄ remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Subsidi ARY Information Ejected, and ä and on Record Safety tab removedFront View IndexRear View Display Panel Remote Control VCR, TV PR +/-,TV +/-, TV Muting Timer Button engages timer-standby mode. pgDA4 Double Azimuth helical Maximum recording time
Top Page Image Contents