JVC HR-S7700EK Subsidi ARY Information, Ejected, and ä and on Record Safety tab removed

58

SUBSIDIARYINFORMATION(cont.)

3.	Tape-to-tape editing is not possible.	● The source (another video recorder,	Confirm that the source is properly
		camcorder) has not been properly	connected.
		connected.
		● All necessary power switches have	Confirm that all units’ power switches
		not been turned on.	are turned on.
		● The input mode is not correct.	Set the input mode to “L-1”,“L-2”,
			“F-1” or “S-1”.
4.	Camcorder recording is not	● The camcorder has not been	Confirm that the camcorder is
	possible.	properly connected.	properly connected.
		● The input mode is not correct.	Set the input mode to “L-1”,“L-2”,
			“F-1” or “S-1”.
TIMER RECORDING
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Timer recording won’t work.	● The clock and/or the timer have	Re-perform the clock and/or timer
		been set incorrectly.	settings.
		● The timer is not engaged.	Press ä and confirm that “ä“ is
			displayed on the display panel.
2.	Timer programming is not possible.	● Timer recording is in progress.	Timer programming can’t be
			performed while a timer recording is
			in progress. Wait until it finishes.
3.	“ä“ and “]“ on the display	● The timer is engaged but there’s no	Load a cassette with the Record
	panel won’t stop blinking.	cassette loaded.	Safety tab intact, or cover the hole
			using adhesive tape.
4.	The cassette is automatically	● The loaded cassette has had its	Remove the cassette and cover the hole
	ejected, and “ä“ and “]“ on the	Record Safety tab removed.	with adhesive tape, or insert a cassette
	display panel won’t stop blinking.		with the Record Safety tab intact.
5.	“ä“ blinks for 10 seconds and the	● ä has been pressed when there are	Check the programmed data and re-
	Timer mode is disengaged.	no programs in memory, or the timer	programme as necessary, then press
		record information has been	ä again.
		programmed incorrectly.
6.	The cassette is automatically	● The end of the tape was reached	The programme may not have been
	ejected, the power shuts off and	during timer recording.	recorded in its entirety. Next time make
	“ä“ and “]“ won’t stop		sure you have enough time on the tape
	blinking.		to record the entire programme.
7.	The VIDEO Plus+ system does not	● The recorder’s preset positions have	Refer to "Guide Program Number Set"
	timer-record properly.	been set incorrectly.	and re-perform the procedure (☞ pg. 45).
OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from	● The camcorder’s microphone is too	Position the camcorder so its
	the TV during camcorder record-	close to the TV.	microphone is away from the TV.
	ing.	● The TV’s volume is too high.	Turn the TV’s volume down.
2.	When scanning channels, some of	● Those channels have been desig-	If you need the skipped channels,
	them are skipped over.	nated to be skipped.	restore them (☞ pg. 50).
3.	The preset cannot be changed.	● Recording is in progress.	Press PAUSE to pause the recording,
			change presets, then press PLAY to
			resume recording.
4.	Channel settings that were made	● After the manual settings were	Perform manual setting again.
	manually seem to have changed or	made, Auto Channel Set was
	disappeared.	performed.
5.	No channels are stored in the	● The TV aerial cable was not	Turn off the recorder once and connect
	recorder's memory.	connected to the recorder when	the TV aerial cable to the recorder
		Auto Set Up was performed.	properly, then turn on the recorder
			again. The recorder will try Auto Set
			Up again (☞ pg. 8).
		● The fully-wired 21-pin SCART cable	Turn off the recorder once and connect
		was not connected between TV and	the fully-wired 21-pin SCART cable to
		the recorder when Preset Download	the recorder properly, then turn on the
		was performed.	recorder again. Then perform Preset
			Download again (☞ pg. 9).