JVC HR-S6850EU, HR-S6852EU, HR-S6851EU 12 EN, Perform Preset Download, Set the video channel

Page 12

12 EN

INITIAL SETTINGS (cont.)

Preset Download

Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide Program Number Set

ATTENTION

You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

If you have connected the recorder to your TV via the AV connection ( pg. 9), the recorder will automatically perform Preset Download instead of the Auto Set Up in step 4 on page 11. After downloading, the recorder sets the clock and Guide Program numbers automatically.

Perform steps 1 to 3 of “Auto Set Up” on page 10 before continuing.

A Perform Preset Download.

Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.

On the front display panel

Press rt to select “CH – –” and press OK or e.

On the on-screen display

Press rt to move the highlight bar (pointer) to “T-V LINK” and press OK or e.

NOTES:

●For details, refer to the instruction manual of your TV.

●In the area where no TV station transmits a PDC (Programme Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.

●If there is a power cut, or if you press 1 or MENU while downloading or set up is in progress, it will be interrupted; be sure to turn off the recorder power once and try again from the beginning.

●Auto Clock Set may not function properly depending on the reception condition.

●On this recorder, the characters available for station names (ID) are A–Z, 0–9, –, f, + and I (space). Some names of

downloaded stations may differ from those of your TV ( pg. 56).

Preset positions on the front display panel increase from “CH1”; do NOT press any button on the recorder or remote control until the front display panel shows clock time, “(CH) 1” or “– –:– –” as illustrated on page 13.

●If you are using the on-screen display, the T-V LINK screen

will appear. Then the GUIDE PROG SET screen will appear during Guide Program Number Set. When Preset Download is completed, “COMPLETED” appears for about 5 seconds, then the normal screen appears.

●If you press any button on the recorder or remote control while downloading is in

progress, it will be interrupted.

B Set the video channel.

Set the video channel to off manually. ( pg. 60)

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Connector cover Front ViewRear View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsCheck the contents Situate the recorderConnect the recorder to TV Connect the recorder to mainsAuto Set Up 10 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or ePerform Preset Download 12 ENSet the video channel Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage 14 ENInstalling Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connectionsSetting satellite receivers brand and channel 16 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 18 ENSlow Motion High-Speed Turbo SearchPause during playback Activate frame-by-frame playback20 EN Variable Speed SearchIndex Search Skip SearchNext Function Memory Repeat PlaybackManual Tracking Soundtrack Selection22 EN Instant Timer Recording ITR Tape Remaining TimeEngage the S-VHS ET mode 24 ENSuper VHS ET S-VHS ET Receiving Stereo and Bilingual ProgrammesPlayback RecordingAccess the Showview screen Access the Showview Program screenBefore performing the Showview Timer Programming 26 ENSet the VPS/PDC mode Access the Title Edit screenEngage the recorder’s timer mode Enter the programme titleExpress Timer Programming 28 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR+Enter the programme mode Before performing the 24 Hour Express Timer Programming30 EN Set the programme start/stop time and channelCancel or change a programme Disengage the timer modeReturn to the timer mode Access the Programme Check screen/displayCancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Overlapping programmes blink on the TV screenSelect the L-2 Select mode Recording modeProgramme Recording Before performing the following stepsNavigation 34 ENNavigation Playback Programme Navigation ScreenLoad a recorded cassette Select a programme36 EN Edit Programme TitleSelect the programme Entering Character Delete Tape DataDelete the tape data Example Enter JVC NewsEdit From a Camcorder 38 ENSet the input mode of recording deck Another Video RecorderAdvantages of S-VHS video recorders Start the source playerOutput/Input Set Select and L-2 Input Setting Decoder connectorConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Select the input mode 44 ENConnect the decoder Set the tunerConnecting/Using a Stereo System Make connectionsMode Set Access the Mode Set screenSelect the mode Select the mode settingWhen viewing overplayed When this function is set to ON, the timer is automaticallyDisengaged when the recorder is powered back on System to on or OFF  pgOn the remote control, or press 7 on the recorder Entire programme while timer-recording in SP mode48 EN Function  pg , set PROG. Navigation to OFFWhen this function is set to ON, you can reduce Power consumption while the recorder is turned offWhen this function is set to ON, you can automatically Correct vertical vibration in the picture when playing back50 EN About Ntsc PlaybackShowview System Setup Guide Program Number SetGuide Program Number Enter the Guide Program numberAccess the Auto Channel Set screen Tuner Set52 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 54 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel56 EN Set Stations aSet Stations B TV Station And ID List Station NameAccess the Clock Set screen Clock Set58 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 60 ENPower 62 EN RecordingOther Problems 64 EN PlaybackSignal-to-noise ratio 45 dB Horizontal resolution Memory backup time Approx minScan system Lines VHS66 EN Memo International telephone Language code Country code
Top Page Image Contents