JVC HR-S6851EU, HR-S6850EU Perform Auto Channel Set, View the Confirmation screen, Press OK twice

Page 53

EN 53

IMPORTANT

In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the SHOWVIEW system, the recorder will record a TV programme of a different station. When programming the

timer using the SHOWVIEW system, be sure to check the desired channel is selected correctly ( pg. 26, “SHOWVIEW® Timer Programming”).

Your video recorder memorizes all detected stations even if

reception of some of them is poor. You can delete those stations with an unacceptable picture ( pg. 55, “Delete A Channel”).

NOTES:

Fine tuning is performed automatically during Auto Channel Set. If you want to perform tuning manually, refer to page 56.

If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED –NO SIGNAL–” appears on the TV screen in step 7. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again.

If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect.

Select the appropriate TV system for those channels ( pg. 55, “INFORMATION”).

F Perform Auto Channel Set.

Press OK twice.

If you have connected the

 

 

recorder and your TV via AV

 

 

connection ( pg. 9), the

 

 

recorder automatically

 

 

performs the Preset

 

 

Download and the T-V LINK

 

 

screen will appear

 

 

( pg. 12).

 

 

The Auto Set screen appears,

Beginning

End

and remains on screen while

the recorder searches for receivable stations.

As Auto Channel Set progresses, the “q” mark on the TV screen moves from left to right. Wait until the TV screen as shown in step 7 appears.

G View the Confirmation screen.

After “SCAN COMPLETED” is displayed on the TV screen for about 5 seconds, the Confirmation screen looking like the one to the right appears. The stations your recorder located appear on a Confirmation screen — channel positions (PR),

channels (CH) and station names (ID –  pg. 57). The blueback screen and the programme currently being broadcast by the blinking station appear alternately for 8 seconds each. To view the next page, use the rt w e button on the remote control.

The stations located in the selected country appear at the top of the list.

The Guide Program numbers will also be set automatically during Auto Channel Set.

H Return to the normal screen.

Press MENU.

Using the Confirmation screen, you can skip or add channel positions, enter station names and perform other operations. Refer to pages 54 – 56 for the procedures.

Depending on reception conditions, the stations may not be stored in order, and the station names may not be stored correctly.

For information on scrambled broadcasts, refer to page 55.

Image 53
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Front Display Panel ON-SCREEN Display Operating JVC TVs How To UseSituate the recorder Check the contentsConnect the recorder to TV Connect the recorder to mains10 EN Auto Set UpTurn on the recorder Select your countrySelect the language Perform Auto Set UpPress rt to select your language code Press rt to select Auto and press OK or e12 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 14 ENSituate the Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connections16 EN Setting satellite receivers brand and channelVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link 18 EN Basic PlaybackHigh-Speed Turbo Search Slow MotionPause during playback Activate frame-by-frame playbackVariable Speed Search 20 ENIndex Search Skip SearchRepeat Playback Next Function MemoryManual Tracking Soundtrack Selection22 EN Tape Remaining Time Instant Timer Recording ITR24 EN Engage the S-VHS ET modeSuper VHS ET S-VHS ET Receiving Stereo and Bilingual ProgrammesRecording PlaybackAccess the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 26 ENAccess the Title Edit screen Set the VPS/PDC modeEngage the recorder’s timer mode Enter the programme title28 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Before performing the 24 Hour Express Timer Programming Enter the programme mode30 EN Set the programme start/stop time and channelDisengage the timer mode Cancel or change a programmeReturn to the timer mode Access the Programme Check screen/displayConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Overlapping programmes blink on the TV screenRecording mode Select the L-2 Select modeProgramme Recording Before performing the following steps34 EN NavigationProgramme Navigation Screen Navigation PlaybackLoad a recorded cassette Select a programmeSelect the programme 36 ENEdit Programme Title Delete Tape Data Entering CharacterDelete the tape data Example Enter JVC News38 EN Edit From a CamcorderAnother Video Recorder Set the input mode of recording deckAdvantages of S-VHS video recorders Start the source playerOutput/Input Set Decoder connector Select and L-2 Input SettingSimple Connections Connecting To a Satellite ReceiverPerfect Connections 44 EN Select the input modeConnect the decoder Set the tunerMake connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingWhen this function is set to ON, the timer is automatically When viewing overplayedDisengaged when the recorder is powered back on System to on or OFF  pgEntire programme while timer-recording in SP mode On the remote control, or press 7 on the recorder48 EN Function  pg , set PROG. Navigation to OFFPower consumption while the recorder is turned off When this function is set to ON, you can reduceWhen this function is set to ON, you can automatically Correct vertical vibration in the picture when playing backAbout Ntsc Playback 50 ENGuide Program Number Set Showview System SetupGuide Program Number Enter the Guide Program numberTuner Set Access the Auto Channel Set screen52 EN Auto Channel SetPress OK twice Perform Auto Channel SetView the Confirmation screen Manual Channel Set 54 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations B 56 ENSet Stations a Station Name TV Station And ID List58 EN Access the Clock Set screenClock Set Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operationExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 60 ENPower Recording 62 ENOther Problems Playback 64 ENMemory backup time Approx min Signal-to-noise ratio 45 dB Horizontal resolutionScan system Lines VHS66 EN Memo Country code International telephone Language code