JVC HR-S6851EU, HR-S6850EU NexTView Link, TV Auto Power On, VCR Auto Standby Direct Rec

Page 17

SAT CONTROL SET (cont.)

EN 17

T-V LINK

G

 

T-V Link Functions

Check the result of the test.

 

 

If the satellite receiver’s channel number has been changed to the same one as you set in step 6 ...

Press rt to move the highlight bar (pointer) to “CHANGED TO ...”, then press OK or e to finish the Sat Control Set mode.

If the satellite receiver’s

channel number has not been changed correctly ...

Press rt to move the highlight bar (pointer) to “NOT CHANGED”, then press OK or e. Then perform the procedure again from step 5.

BRAND NAME

CODE

 

 

JVC

73

AMSTRAD

60, 61, 62, 63, 92

CANAL SATELLITE

81

CANAL +

81

D-BOX

85

ECHOSTAR

78, 79, 80

ECHOSTAR (VIA DIGITAL)

82

FINLUX

68

FORCE

89

GALAXIS

88

GRUNDIG

64, 65

HIRSCHMANN

64, 78, 99

ITT NOKIA

68

JERROLD

75

KATHREIN

70, 71, 96

LUXOR

68

MASCOM

93

MASPRO

70

NOKIA

87, 94

PACE

65, 67, 74, 86, 92

PANASONIC

74, 92

PHILIPS

66, 84

RFT

69

SABA

97

SAGEM

83, 90

SALORA

68

SIEMENS

64

SKYMASTER

69, 98

THOMSON

97

TPS

83

TRIAX

91

WISI

64

 

 

When you connect the recorder to your TV via a fully-wired 21-pin SCART cable ( pg. 9), the following functions are available. You can use these functions only with a TV offering T-V Link, etc.*

For details, refer to the instruction manual of your TV.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

NexTView Link

You can download the EPG (Electronic Programme Guide) information from your TV for timer-programming on the recorder.

For details, refer to the instruction manual of your TV.

TV Auto Power On

The TV will turn on and be set to its AV mode automatically whenever you play a tape.

For details, refer to the instruction manual of your TV.

VCR Auto Standby

You can use your TV’s remote control to turn off the recorder. For details, refer to the instruction manual of your TV.

Direct Rec

You can easily start recording the programme that you are watching on your TV. When you use this function, set “DIRECT REC” to “ON” ( pg. 48).

NOTES:

The Satellite Controller may not work with all types of satellite receiver.

For some satellite receivers, you need to set its channel input mode to 2-digit.

If your satellite receiver has more than two channel modes, be sure to set to “All Channel Mode”. For details, refer to the instruction manual of the satellite receiver.

When selecting the satellite receiver’s channel ( step 6), signals from the remote control may interfere with signals transmitted from the Satellite Controller. In this case, move the remote control as close to the recorder’s infrared beam receiving window as possible.

Image 17
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Front Display Panel ON-SCREEN Display Operating JVC TVs How To UseSituate the recorder Check the contentsConnect the recorder to TV Connect the recorder to mains10 EN Auto Set UpTurn on the recorder Select your countrySelect the language Perform Auto Set UpPress rt to select your language code Press rt to select Auto and press OK or e12 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 14 ENSituate the Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connections16 EN Setting satellite receivers brand and channelVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link 18 EN Basic PlaybackHigh-Speed Turbo Search Slow MotionPause during playback Activate frame-by-frame playbackVariable Speed Search 20 ENIndex Search Skip SearchRepeat Playback Next Function MemoryManual Tracking Soundtrack Selection22 EN Tape Remaining Time Instant Timer Recording ITR24 EN Engage the S-VHS ET modeSuper VHS ET S-VHS ET Receiving Stereo and Bilingual ProgrammesRecording PlaybackAccess the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 26 ENAccess the Title Edit screen Set the VPS/PDC modeEngage the recorder’s timer mode Enter the programme title28 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Before performing the 24 Hour Express Timer Programming Enter the programme mode30 EN Set the programme start/stop time and channelDisengage the timer mode Cancel or change a programmeReturn to the timer mode Access the Programme Check screen/displayConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Overlapping programmes blink on the TV screenRecording mode Select the L-2 Select modeProgramme Recording Before performing the following steps34 EN NavigationProgramme Navigation Screen Navigation PlaybackLoad a recorded cassette Select a programmeSelect the programme 36 ENEdit Programme Title Delete Tape Data Entering CharacterDelete the tape data Example Enter JVC News38 EN Edit From a CamcorderAnother Video Recorder Set the input mode of recording deckAdvantages of S-VHS video recorders Start the source playerOutput/Input Set Decoder connector Select and L-2 Input SettingSimple Connections Connecting To a Satellite ReceiverPerfect Connections 44 EN Select the input modeConnect the decoder Set the tunerMake connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingWhen this function is set to ON, the timer is automatically When viewing overplayedDisengaged when the recorder is powered back on System to on or OFF  pgEntire programme while timer-recording in SP mode On the remote control, or press 7 on the recorder48 EN Function  pg , set PROG. Navigation to OFFPower consumption while the recorder is turned off When this function is set to ON, you can reduceWhen this function is set to ON, you can automatically Correct vertical vibration in the picture when playing backAbout Ntsc Playback 50 ENGuide Program Number Set Showview System SetupGuide Program Number Enter the Guide Program numberTuner Set Access the Auto Channel Set screen52 EN Auto Channel SetPress OK twice Perform Auto Channel SetView the Confirmation screen Manual Channel Set 54 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations B 56 ENSet Stations a Station Name TV Station And ID List58 EN Access the Clock Set screenClock Set Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operationExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 60 ENPower Recording 62 ENOther Problems Playback 64 ENMemory backup time Approx min Signal-to-noise ratio 45 dB Horizontal resolutionScan system Lines VHS66 EN Memo Country code International telephone Language code