JVC HR-S6850EU, HR-S6852EU Programme Recording, Select the L-2 Select mode, Recording mode

Page 33

EN 33

Automatic Satellite

Programme

Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder’s AV2 (L-2) IN/DECODER connector and programme the timer on the satellite receiver. The recorder starts or stops recording by the signals input from the satellite receiver. After recording, the recorder’s power shuts off automatically.

SAT# indicator

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver’s power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Automatic Satellite Programme Recording mode; otherwise, the recorder will start recording when the connected appliance’s power is turned on.

●Automatic Satellite Programme Recording and timer-recording cannot be done at the same time.

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder’s AV2 (L-2) IN/DECODER connector. ( pg. 42, 43)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

A Select the L-2 SELECT mode.

Set “L-2 SELECT” to “A/V” or “SAT” ( pg. 41).

●When you select “SAT”, refer to “IMPORTANT” on page 42.

B Set the tape speed.

Press SP/LP/EP (p).

● It is not possible to select EP mode if “COLOUR SYSTEM” is

set to “MESECAM”. ( pg. 50)

C Engage the Automatic Satellite Programme

Recording mode.

Press and hold SAT# for about 2 seconds. The SAT# indicator lights up and the recorder turns off automatically.

NOTES:

●To disengage the Automatic Satellite Programme Recording mode, press SAT#. The SAT# indicator goes off.

●If the recorder’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.

●In step 3, if the SAT# indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic

Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer Programming” ( pg. 28) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.

●The SAT# indicator blinks while Automatic Satellite Programme Recording is in progress.

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

●Pressing the recorder’s 1 button while Automatic Satellite Programme Recording is in progress turns off the recorder’s power and disengages the Automatic Satellite Programme Recording mode.

●If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible to set different tape speeds for each programme.

●Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not start Automatic Satellite Programme Recording even though the SAT# indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer.

●The B.E.S.T. system ( pg. 25) does not work while Automatic Satellite Programme Recording is in progress.

●Just Clock ( pg. 58) does not work when the Automatic Satellite Programme Recording mode is engaged.

●When the Automatic Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Automatic Satellite

Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON” ( pg. 47).

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Front Display Panel ON-SCREEN Display Operating JVC TVs How To UseSituate the recorder Check the contentsConnect the recorder to TV Connect the recorder to mains10 EN Auto Set UpTurn on the recorder Select your countrySelect the language Perform Auto Set UpPress rt to select your language code Press rt to select Auto and press OK or e12 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 14 ENSituate the Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connections16 EN Setting satellite receivers brand and channelTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec 18 EN Basic PlaybackHigh-Speed Turbo Search Slow MotionPause during playback Activate frame-by-frame playbackVariable Speed Search 20 ENIndex Search Skip SearchRepeat Playback Next Function MemoryManual Tracking Soundtrack Selection22 EN Tape Remaining Time Instant Timer Recording ITR24 EN Engage the S-VHS ET modeSuper VHS ET S-VHS ET Receiving Stereo and Bilingual ProgrammesRecording PlaybackAccess the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 26 ENAccess the Title Edit screen Set the VPS/PDC modeEngage the recorder’s timer mode Enter the programme title28 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Before performing the 24 Hour Express Timer Programming Enter the programme mode30 EN Set the programme start/stop time and channelDisengage the timer mode Cancel or change a programmeReturn to the timer mode Access the Programme Check screen/displayConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Overlapping programmes blink on the TV screenRecording mode Select the L-2 Select modeProgramme Recording Before performing the following steps34 EN NavigationProgramme Navigation Screen Navigation PlaybackLoad a recorded cassette Select a programme36 EN Edit Programme TitleSelect the programme Delete Tape Data Entering CharacterDelete the tape data Example Enter JVC News38 EN Edit From a CamcorderAnother Video Recorder Set the input mode of recording deckAdvantages of S-VHS video recorders Start the source playerOutput/Input Set Decoder connector Select and L-2 Input SettingSimple Connections Connecting To a Satellite ReceiverPerfect Connections 44 EN Select the input modeConnect the decoder Set the tunerMake connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingWhen this function is set to ON, the timer is automatically When viewing overplayedDisengaged when the recorder is powered back on System to on or OFF  pgEntire programme while timer-recording in SP mode On the remote control, or press 7 on the recorder48 EN Function  pg , set PROG. Navigation to OFFPower consumption while the recorder is turned off When this function is set to ON, you can reduceWhen this function is set to ON, you can automatically Correct vertical vibration in the picture when playing backAbout Ntsc Playback 50 ENGuide Program Number Set Showview System SetupGuide Program Number Enter the Guide Program numberTuner Set Access the Auto Channel Set screen52 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice Manual Channel Set 54 ENDelete a Channel When Receiving a Scrambled Broadcast56 EN Set Stations aSet Stations B Station Name TV Station And ID ListAccess the Clock Set screen Clock Set58 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operationExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 60 ENPower Recording 62 ENOther Problems Playback 64 ENMemory backup time Approx min Signal-to-noise ratio 45 dB Horizontal resolutionScan system Lines VHS66 EN Memo Country code International telephone Language code
Top Page Image Contents