JVC HR-S6850EU 30 EN, Enter the programme mode, Set the programme start/stop time and channel

Page 30

30 EN

TIMER RECORDING (cont.)

24 Hour Express Timer Programming

Before performing the 24 Hour Express Timer Programming:

Make sure that the recorder’s built-in clock is set properly.

Insert a cassette with the safety tab in place. The recorder will come on automatically.

Set the tape speed.

NOTES:

You can programme this recorder to timer-record as many as

8 programmes. If you try to programme the recorder to record a ninth, “FULL” appears on the front display panel. To record

the extra programme, you must first cancel any unnecessary programmes ( pg. 31).

It is not possible to timer-record a satellite broadcast received on the channel position “0” by the satellite receiver.

If “Err” appears on the front display panel, repeat the above steps again.

When a menu screen is shown, you cannot use 24 Hour Express Timer Programming function. Press MENU to return to normal screen, and try again.

You can use 24 Hour Express Timer Programming function also when the recorder is turned off.

For 24 Hour Express Timer Programming function, the programme overlap warning display does not appear even if some programmes overlap each other. The programme with the lower programme number will be recorded and the other one will not be recorded correctly.

You can programme a timer recording that starts within 24 hours using the JOG dial on the recorder.

A Enter the programme mode.

Press 24H EXPRESS # on the recorder. The start time indicator ( ) starts blinking on the front display panel.

The current tape speed and VPS/PDC setting appear on the front display panel, but it is impossible to change the setting.

You can only change the setting after programming ( pg. 31).

B Set the programme start/stop time and channel.

Turn the JOG dial to the left or right to set the time you want recording to start.

One click stop of the JOG dial changes the time in 5-minute intervals.

Push the JOG dial. The stop time indicator ( ) starts blinking on the front display panel. Turn the JOG dial to the left or right to set the time you want recording to stop.

Push the JOG dial. Turn the JOG dial to the left or right to select the channel you wish to record.

You can cancel the setting at any time by pressing and holding the JOG dial for more than 3 seconds or pressing & on the remote control. Repeat the step 2.

C Engage the recorder’s timer mode.

Press 24H EXPRESS #. The recorder turns off automatically and ”#” appears on the front display panel.

To disengage the timer mode, press # (TIMER) or 24H EXPRESS # again.

Image 30
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Connector cover Front ViewRear View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsConnect the recorder to TV Check the contentsSituate the recorder Connect the recorder to mainsTurn on the recorder Auto Set Up10 EN Select your countryPress rt to select your language code Perform Auto Set UpSelect the language Press rt to select Auto and press OK or eSet the video channel Perform Preset Download12 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 14 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 16 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 18 ENPause during playback Slow MotionHigh-Speed Turbo Search Activate frame-by-frame playbackIndex Search 20 ENVariable Speed Search Skip SearchManual Tracking Next Function MemoryRepeat Playback Soundtrack Selection22 EN Instant Timer Recording ITR Tape Remaining TimeSuper VHS ET S-VHS ET Engage the S-VHS ET mode24 EN Receiving Stereo and Bilingual ProgrammesPlayback RecordingBefore performing the Showview Timer Programming Access the Showview screenAccess the Showview Program screen 26 ENEngage the recorder’s timer mode Set the VPS/PDC modeAccess the Title Edit screen Enter the programme titleExpress Timer Programming 28 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR+30 EN Enter the programme modeBefore performing the 24 Hour Express Timer Programming Set the programme start/stop time and channelReturn to the timer mode Cancel or change a programmeDisengage the timer mode Access the Programme Check screen/displaySelect the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenProgramme Recording Select the L-2 Select modeRecording mode Before performing the following stepsNavigation 34 ENLoad a recorded cassette Navigation PlaybackProgramme Navigation Screen Select a programme36 EN Edit Programme TitleSelect the programme Delete the tape data Entering CharacterDelete Tape Data Example Enter JVC NewsEdit From a Camcorder 38 ENAdvantages of S-VHS video recorders Set the input mode of recording deckAnother Video Recorder Start the source playerOutput/Input Set Select and L-2 Input Setting Decoder connectorConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Connect the decoder Select the input mode44 EN Set the tunerConnecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingDisengaged when the recorder is powered back on When viewing overplayedWhen this function is set to ON, the timer is automatically System to on or OFF  pg48 EN On the remote control, or press 7 on the recorderEntire programme while timer-recording in SP mode Function  pg , set PROG. Navigation to OFFWhen this function is set to ON, you can automatically When this function is set to ON, you can reducePower consumption while the recorder is turned off Correct vertical vibration in the picture when playing back50 EN About Ntsc PlaybackGuide Program Number Showview System SetupGuide Program Number Set Enter the Guide Program number52 EN Access the Auto Channel Set screenTuner Set Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 54 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel56 EN Set Stations aSet Stations B TV Station And ID List Station NameAccess the Clock Set screen Clock Set58 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 60 ENPower 62 EN RecordingOther Problems 64 EN PlaybackScan system Signal-to-noise ratio 45 dB Horizontal resolutionMemory backup time Approx min Lines VHS66 EN Memo International telephone Language code Country code