JVC HR-S7600AM specifications Tape-To-Tape Editing, Playback equipment, Dubbed tape

Page 51

EN51

Playback

This recorder can play back all 3 types of recorded tape.

Recorded tape

HR-S7600AM

PAL

MESECAM

NTSC

Playback circuit

PAL

MESECAM

NTSC[PAL

NTSC 3.58 MHz

Built-in

RFconverter

G, K, I, H, M

	Multi-system receiver
	PAL
	(B/G, D/K, I, H)
RF OUT	NTSC (M)
RF OUT
	Multi-system monitor

Manual switching

Manual switching

NTSC 4.43 MHz

VIDEO OUT AUDIO OUT

PAL

SECAM

NTSC 3.58

NTSC 4.43

NOTES:

When viewing NTSC tapes on a PAL TV set:

●The picture may shrink vertically with black bars appearing at the top and bottom of the screen. This is not a malfunction on the part of the video recorder nor the TV.

●The picture may roll up or down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)

●During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.

ATTENTION:

When this recorder is connected to a multi-system TV, the audio signal may not be heard or may be noisy if the colour system select switch of the TV is adjusted to the AUTO position. In such a case, set the TV's colour system select switch to the appropri- ate position which corresponds to the TV system you have selected at the TV System Select screen.

Tape-To-Tape Editing

There are 4 different types of recorded tape, depending on the signal recorded.

Recorded tape

PAL

MESECAM

SECAM

NTSC

Playback equipment

PAL

MESECAM

SECAM

NTSC 3.58 MHz

NTSC 4.43 MHz

HR-S7600AM

PAL

MESECAM

Recording circuit

NTSC 3.58 MHz

NTSC 4.43 MHz

Dubbed tape

PAL

MESECAM

NTSC

Image 51

Contents HR-S7600AM Safety Precautions Moisture Condensation Mains Check ContentsBasic Connections Situate RecorderVideo Connection Connect Recorder to TVConnect Recorder to Mains With RF Connection Access Video Channel SET ModeVideo Channel Set Select TV SystemSET SET Video ChannelFinish Video Channel SET Finish Video ChannelSET Year Auto Set UpSelect Language SET DatePress OK or Push JOG Þ During Auto Set UpStart Auto Channel SET Major Countries TV SystemOn-Screen Displays Select Language Access Initial SET ScreenStart Clock Operation Access Clock SET ScreenClock Set SET TimeStart Playback Basic PlaybackLoad a Cassette PointSlow Motion Playback FeaturesPlayback Still Picture/Frame-By-Frame PlaybackSections Adjust Tracking ManuallyActivate HIGH-SPEED Search Skip Over UnwantedDigital TBC/NR Access Main MenuActivate Digital TBC/NR Digital 3RSoundtrack Selection Tape Position Indicator Instant ReViewActivate Instant Review Next Function MemoryTimeScan Variable-Speed SearchPause Menu Push JOG Speed LP TimeScanTimeScan Audio Speed SPBasic Recording SET Recording Duration Recording FeaturesEngage ITR Mode Select Channel to WatchElapsed Recording Time Indication Reset CounterSET Counter Display Display Remaining TimeType of Broadcast Receiving Stereo Bilingual ProgrammesTo Record Stereo And Bilingual Programmes A2 To Record Nicam Stereo And Bilingual ProgrammesET and VHS Select S-VHS ModeAccess Main Menu Screen VHS Super VHS, S-VHSSelect S-VHS ET SET ModeSuper VHS ET S.T. Picture System PreparationJogþ During B.E.S.T RecordingPlayback Or press Record on the recorderGuide Program Number Set System SetupAccess G-CODE Showview Setup Screen NumberEnter Receiving Channel Position Number Number keys to input Number of the recordersReceived. Then press OK or Access G-CODE Showview Screen CODETimer ProgrammingTimer Mode Return to NormalEngage Recorders Enter Programme Date Express Timer ProgrammingAccess Programme Enter Programme Stop TimeWeekly Timer Or OK. Program Completed appears onScreen for about 5 seconds, then normal screen Disengage Timer Mode Return to Timer ModeCheck, Cancel And Replace Programmes Auto SP→LP Timer Auto TimerAuto SP→LP Timer RE-SUPPLY Power Remote Control FunctionsRemove Power Supply SET Remote Control CodeTV Brand Name Code TV Multi-brand Remote ControlSET TV Brand Code Operate TVReturn to Normal Screen SET ModePreparation For Editing Picture ControlPlayer If the camcorder has no S-VIDEO output connector RecorderIf the camcorder has an S-VIDEO output connector Recorder Edit From CamcorderSynchro Editing Start Recording Deck SET Recording Decks Input ModeEdit To Or From Another Video Recorder Start Source PlayerLocate Start Point SET Input ModeAudio Dubbing Engage Audio DubbingStart Dubbing END Audio DubbingPlay Stop Pause Reset the Counter Insert EditingLocate END Point END Insert Editing Start EditingRandom Assemble Editing Access R.A. Edit ScreenAudio signal Video signal CancelEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditAccess Initial SET Access Jlip ID NO. SET ScreenTerminal JLIPJoint Level Interface Protocol Connector Audio Cable not provided Connecting Using a Stereo SystemOff-Air Recording Setting Of The Colour System Select ButtonsMode Display Mode DescriptionTape-To-Tape Editing Playback equipmentDubbed tape Auto CH SET, then Auto Channel SetTuner SET, then press OK or Push JogþSET Desired Station Access Tuner SETAccess Channel List Select PositionDelete a Channel Swap Channel PositionsJOG% Push JOG Þ Fine-Tuning ChannelsPress Play to turn the indicator off Check the cassette If youre using the RF OUT connec- tionTimer again Timer record information has beenNew one. pg RoubleshootingQuest Ions and Answers Index Display Panel EN Index Maximum recording time Supplied fresh battery actualHR-S7600AM