JVC HR-S7600AM SET TV Brand Code, Operate TV, TV Multi-brand Remote Control, TV Brand Name Code

Page 37

V

VCR TV/VCR

EN37

TV Multi-brand Remote

Control

Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer's TVs can also be controlled.

Before you start . . .

Turn on the TV using its remote control.

1 2

4 5

7 8

CANCEL0

1

STOP

3

TV PROG+/–

3

2

6NUMBER

9

TIMER

4

OK

TV VOL+/–

1

2

SET TV BRAND CODE

Refer to the chart below. While holding down TV on the recorder's remote control, enter your TV's brand code using the NUMBER keys, then press STOP.

Check if the TV's power goes off as it should. If it does, try other operations (step 2).

Once you have set the remote control to operate the TV, you don't have to repeat this step until you replace your remote control's batteries.

Some TV brands have more than one code. If the TV does not function with one code, try entering another.

OPERATE TV

First, press TV to set the remote control to TV mode, then press the corresponding button: , TV PROG +/–,

TV/VCR, TV VOL +/– (Volume), (Muting), NUMBER keys.

For some brands of TV, you must press OK after having pressed the NUMBER keys.

ATTENTION

The remote control can operate not only the video recorder but also some of your TV's functions.

To operate your video recorder, first press the VCR button to set the remote control to the Video mode.

To operate your TV, first press the TV button to set the remote control to the TV mode.

Control Your TV Using Additional Buttons

Use the NUMBER keys, and the button, CANCEL button or TIMER button to select the TV's channel.

With televisions under Code 01, 02, 03, 05, 07, 15, 16,

22, 23, 26 or 27, the button corresponds to the 1- digit/2-digit entry switching button (often labelled – /– –) of your TV's remote control.

With televisions under Code 01, 08, 18, 19, 24 or 25, the CANCEL button corresponds to the 10 + button, and the TIMER button corresponds to the 20 + button of your TV's remote control.

NOTE:

The way these buttons are used is determined by your TV. Use these buttons as instructed for your TV's remote control.

IMPORTANT

Although the provided remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability.

TV BRAND NAME

CODE

JVC

01

AIWA

10

BEIJING

05, 27

CHANGHONG

05, 06, 16, 25

DAEWOO

11

FERGUSON

15

FINLUX

20

FUNAI

09

GRUNDIG

17

HITACHI

07

ITT

18

JINXING

23

KONKA

26

LG/GOLDSTAR

13

MITSUBISHI

06

MIVER

19

NEC

22

NOBLEX

27

NOKIA

21

PANASONIC

02

PEONY

23, 24, 25

PHILICO

07

PHILIPS

16

SAMSUNG

12, 16

SANYO

08

SHARP

04

SONY

03

TCL

16, 28

THOMSON

14

TOSHIBA

05

Image 37
Contents HR-S7600AM Safety Precautions Moisture Condensation Basic Connections Check ContentsSituate Recorder MainsConnect Recorder to TV Video ConnectionConnect Recorder to Mains Video Channel Set Access Video Channel SET ModeSelect TV System With RF ConnectionFinish Video Channel SET SET Video ChannelFinish Video Channel SETSelect Language Auto Set UpSET Date SET YearStart Auto Channel SET During Auto Set UpMajor Countries TV System Press OK or Push JOG ÞOn-Screen Displays Select Language Access Initial SET ScreenClock Set Access Clock SET ScreenSET Time Start Clock OperationLoad a Cassette Basic PlaybackPoint Start PlaybackPlayback Playback FeaturesStill Picture/Frame-By-Frame Playback Slow MotionActivate HIGH-SPEED Search Adjust Tracking ManuallySkip Over Unwanted SectionsActivate Digital TBC/NR Access Main MenuDigital 3R Digital TBC/NRActivate Instant Review Tape Position Indicator Instant ReViewNext Function Memory Soundtrack SelectionVariable-Speed Search TimeScanPause Menu Push JOG TimeScan Audio TimeScanSpeed SP Speed LPBasic Recording Engage ITR Mode Recording FeaturesSelect Channel to Watch SET Recording DurationSET Counter Display Reset CounterDisplay Remaining Time Elapsed Recording Time IndicationTo Record Stereo And Bilingual Programmes A2 Receiving Stereo Bilingual ProgrammesTo Record Nicam Stereo And Bilingual Programmes Type of BroadcastAccess Main Menu Screen Select S-VHS ModeVHS Super VHS, S-VHS ET and VHSMode Select S-VHS ET SETSuper VHS ET Preparation S.T. Picture SystemJogþ Playback RecordingOr press Record on the recorder During B.E.S.TAccess G-CODE Showview Setup Screen System SetupNumber Guide Program Number SetNumber keys to input Number of the recorders Enter Receiving Channel Position NumberReceived. Then press OK or Access G-CODE Showview Screen CODETimer ProgrammingReturn to Normal Timer ModeEngage Recorders Access Programme Express Timer ProgrammingEnter Programme Stop Time Enter Programme DateOr OK. Program Completed appears on Weekly TimerScreen for about 5 seconds, then normal screen Return to Timer Mode Disengage Timer ModeCheck, Cancel And Replace Programmes Auto Timer Auto SP→LP TimerAuto SP→LP Timer Remove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerSET TV Brand Code TV Multi-brand Remote ControlOperate TV TV Brand Name CodePreparation For Editing SET ModePicture Control Return to Normal ScreenIf the camcorder has an S-VIDEO output connector Recorder If the camcorder has no S-VIDEO output connector RecorderEdit From Camcorder PlayerSynchro Editing Edit To Or From Another Video Recorder SET Recording Decks Input ModeStart Source Player Start Recording DeckAudio Dubbing SET Input ModeEngage Audio Dubbing Locate Start PointEND Audio Dubbing Start DubbingPlay Stop Pause Insert Editing Reset the CounterLocate END Point END Insert Editing Start EditingAudio signal Video signal Access R.A. Edit ScreenCancel Random Assemble EditingLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditAccess Jlip ID NO. SET Screen Access Initial SETTerminal JLIPJoint Level Interface Protocol Connector Audio Cable not provided Connecting Using a Stereo SystemMode Display Setting Of The Colour System Select ButtonsMode Description Off-Air RecordingPlayback equipment Tape-To-Tape EditingDubbed tape Tuner SET, then press Auto Channel SetOK or Push Jogþ Auto CH SET, thenAccess Channel List Access Tuner SETSelect Position SET Desired StationSwap Channel Positions Delete a ChannelJOG% Push JOG Þ Fine-Tuning ChannelsPress Play to turn the indicator off Check the cassette If youre using the RF OUT connec- tionTimer again Timer record information has beenNew one. pg RoubleshootingQuest Ions and Answers Index Display Panel EN Index Maximum recording time Supplied fresh battery actualHR-S7600AM