JVC HR-S7600AM Start Auto Channel SET, Major Countries TV System, Press OK or Push JOG Þ

Page 9

Major Countries

TV System

 

 

Australia, New Zealand, Kuwait, U.A.E.,

 

Indonesia, Singapore, Thailand, Malaysia,

B/G

Iran, Saudi Arabia, Egypt, Morocco,

 

Lebanon, Iraq

 

 

 

China, Mongolia, Russia

D/K

 

 

Hong Kong

I

 

 

U.S.A., Japan, S.Korea, Taiwan

M

 

 

0

4

 

1

OK

PUSH JOG

5

6

EN9

SELECT TV SYSTEM

Press PUSH JOG to place the pointer next to the appropriate TV system (refer to the table on the left).

START AUTO CHANNEL SET

Press OK or PUSH JOG Þ .

The Auto Set Up function scans all the channels that are receivable by your recorder. It then automatically assigns each receivable channel to the TV PROG buttons. It skips non-receivable channels.

As Auto Set Up progresses, the " " mark on the

screen moves from left to right. (See below.)

DO NOT press any button on the recorder or remote control while Auto Set Up is in progress.

AUTO CH SET

PLEASE WAIT

STARTFINISH

During Auto Set Up

"PLEASE WAIT" blinks on the screen and "Auto" blinks on the front display panel.

TV Screen

When Auto Set Up is completed, the lowest position number will appear on the front display panel.

NOTES:

If you perform Auto Set Up when the aerial cable is not connected properly, "SCAN COMPLETED -NO SIGNAL-" appears on the screen. When this happens, make sure of the aerial connection and press OK; Auto Set Up will take place again.

If there is a power cut, or if you press or MENU while Auto Set Up is in progress, Auto Set Up will be interrupted; be sure to turn off the recorder power once and try again.

If you want to set the tuner manually such as to add or skip channels, to swap channel positions, or to fine-tune channels, pg. 53 – 55.

If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels. "TV System Selection – When you see the picture but the audio can't be heard or sounds unnatural" on page 55.

Image 9
Contents HR-S7600AM Safety Precautions Moisture Condensation Basic Connections Check ContentsSituate Recorder MainsVideo Connection Connect Recorder to TVConnect Recorder to Mains Video Channel Set Access Video Channel SET ModeSelect TV System With RF ConnectionFinish Video Channel SET SET Video ChannelFinish Video Channel SETSelect Language Auto Set UpSET Date SET YearStart Auto Channel SET During Auto Set UpMajor Countries TV System Press OK or Push JOG ÞOn-Screen Displays Select Language Access Initial SET ScreenClock Set Access Clock SET ScreenSET Time Start Clock OperationLoad a Cassette Basic PlaybackPoint Start PlaybackPlayback Playback FeaturesStill Picture/Frame-By-Frame Playback Slow MotionActivate HIGH-SPEED Search Adjust Tracking ManuallySkip Over Unwanted SectionsActivate Digital TBC/NR Access Main MenuDigital 3R Digital TBC/NRActivate Instant Review Tape Position Indicator Instant ReViewNext Function Memory Soundtrack SelectionTimeScan Variable-Speed SearchPause Menu Push JOG TimeScan Audio TimeScanSpeed SP Speed LPBasic Recording Engage ITR Mode Recording FeaturesSelect Channel to Watch SET Recording DurationSET Counter Display Reset CounterDisplay Remaining Time Elapsed Recording Time IndicationTo Record Stereo And Bilingual Programmes A2 Receiving Stereo Bilingual ProgrammesTo Record Nicam Stereo And Bilingual Programmes Type of BroadcastAccess Main Menu Screen Select S-VHS ModeVHS Super VHS, S-VHS ET and VHSSelect S-VHS ET SET ModeSuper VHS ET S.T. Picture System PreparationJogþ Playback RecordingOr press Record on the recorder During B.E.S.TAccess G-CODE Showview Setup Screen System SetupNumber Guide Program Number SetEnter Receiving Channel Position Number Number keys to input Number of the recordersReceived. Then press OK or Access G-CODE Showview Screen CODETimer ProgrammingTimer Mode Return to NormalEngage Recorders Access Programme Express Timer ProgrammingEnter Programme Stop Time Enter Programme DateWeekly Timer Or OK. Program Completed appears onScreen for about 5 seconds, then normal screen Disengage Timer Mode Return to Timer ModeCheck, Cancel And Replace Programmes Auto SP→LP Timer Auto TimerAuto SP→LP Timer Remove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerSET TV Brand Code TV Multi-brand Remote ControlOperate TV TV Brand Name CodePreparation For Editing SET ModePicture Control Return to Normal ScreenIf the camcorder has an S-VIDEO output connector Recorder If the camcorder has no S-VIDEO output connector RecorderEdit From Camcorder PlayerSynchro Editing Edit To Or From Another Video Recorder SET Recording Decks Input ModeStart Source Player Start Recording DeckAudio Dubbing SET Input ModeEngage Audio Dubbing Locate Start PointStart Dubbing END Audio DubbingPlay Stop Pause Reset the Counter Insert EditingLocate END Point END Insert Editing Start EditingAudio signal Video signal Access R.A. Edit ScreenCancel Random Assemble EditingLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditAccess Initial SET Access Jlip ID NO. SET ScreenTerminal JLIPJoint Level Interface Protocol Connector Audio Cable not provided Connecting Using a Stereo SystemMode Display Setting Of The Colour System Select ButtonsMode Description Off-Air RecordingTape-To-Tape Editing Playback equipmentDubbed tape Tuner SET, then press Auto Channel SetOK or Push Jogþ Auto CH SET, thenAccess Channel List Access Tuner SETSelect Position SET Desired StationDelete a Channel Swap Channel PositionsJOG% Push JOG Þ Fine-Tuning ChannelsPress Play to turn the indicator off Check the cassette If youre using the RF OUT connec- tionTimer again Timer record information has beenNew one. pg RoubleshootingQuest Ions and Answers Index Display Panel EN Index Maximum recording time Supplied fresh battery actualHR-S7600AM