JVC HR-S7600AM specifications SET Video Channel, Finish Video Channel SET, Set

Page 7

3

4

SET VIDEO CHANNEL

Set your TV to UHF channel 36.

If the two vertical white bars appear clearly on the screen as shown in the illustration ("TEST SIGNAL" on page 6), press OK and then go to step 4.

If the two vertical white bars do not appear clearly, press OK and then TV PROG + or to set the video recorder to a vacant channel between 28 and 60 which is not occupied by any local station in your area.

(Ex.) If channel 50 is available in your area

Then set your TV to UHF channel 50 and check if the two vertical white bars appear clearly on the screen; if so, go to step 4. If not, re-set the video recorder to another vacant channel and try again.

NOTES:

If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

If you cannot obtain the two vertical white bars clearly with any channel between 28 and 60, consult your JVC dealer.

FINISH VIDEO CHANNEL SET

Press OK.

If Auto Set Up (pg. 8) or Tuner Set (pg. 52) has not previously been performed, the Language Select screen appears and Auto Set Up function takes place automatically.

EN7

With AV Connection or

S-VIDEO Connection

IMPORTANT:

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

ACCESS VIDEO CHANNEL SET MODE

 

 

Hold down STOP/EJECT on the recorder until the

1 display panel shows the following.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SET VIDEO CHANNEL

 

 

Press OK, then press TV PROG – until the display panel

2

shows the following.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Now the video channel is set to off (– –).

 

 

 

 

 

 

 

 

 

FINISH VIDEO CHANNEL

3

 

SET

 

Press OK.

 

 

 

 

 

 

If Auto Set Up (pg. 8) or Tuner Set (pg. 52) has

 

 

not previously been performed, the Language Select

 

 

 

screen appears and Auto Set Up function takes place

 

 

 

automatically.

To view picture signals from the video recorder, set your TV to its AV mode.

Be sure to connect the power plug to an AC outlet first before installing the lithium battery; otherwise, the battery's service life will be drastically shortened.

Installing/Removing the lithium battery

1Make sure that the power plug is connected to an AC outlet

and turn off the recorder power.

2Open the battery cover while pressing the release tab as

illustrated.

3Insert a lithium battery with the plus (+) side up and push it in.

To remove the lithium battery, press the latch A down- ward using a pointed non-metallic object, then pull out

the lithium battery.

4Close the battery cover until it clicks in place.

A

Image 7
Contents HR-S7600AM Safety Precautions Moisture Condensation Mains Check ContentsBasic Connections Situate RecorderConnect Recorder to TV Video ConnectionConnect Recorder to Mains With RF Connection Access Video Channel SET ModeVideo Channel Set Select TV SystemSET SET Video ChannelFinish Video Channel SET Finish Video ChannelSET Year Auto Set UpSelect Language SET DatePress OK or Push JOG Þ During Auto Set UpStart Auto Channel SET Major Countries TV SystemOn-Screen Displays Select Language Access Initial SET ScreenStart Clock Operation Access Clock SET ScreenClock Set SET TimeStart Playback Basic PlaybackLoad a Cassette PointSlow Motion Playback FeaturesPlayback Still Picture/Frame-By-Frame PlaybackSections Adjust Tracking ManuallyActivate HIGH-SPEED Search Skip Over UnwantedDigital TBC/NR Access Main MenuActivate Digital TBC/NR Digital 3RSoundtrack Selection Tape Position Indicator Instant ReViewActivate Instant Review Next Function MemoryVariable-Speed Search TimeScanPause Menu Push JOG Speed LP TimeScanTimeScan Audio Speed SPBasic Recording SET Recording Duration Recording FeaturesEngage ITR Mode Select Channel to WatchElapsed Recording Time Indication Reset CounterSET Counter Display Display Remaining TimeType of Broadcast Receiving Stereo Bilingual ProgrammesTo Record Stereo And Bilingual Programmes A2 To Record Nicam Stereo And Bilingual ProgrammesET and VHS Select S-VHS ModeAccess Main Menu Screen VHS Super VHS, S-VHSMode Select S-VHS ET SETSuper VHS ET Preparation S.T. Picture SystemJogþ During B.E.S.T RecordingPlayback Or press Record on the recorderGuide Program Number Set System SetupAccess G-CODE Showview Setup Screen NumberNumber keys to input Number of the recorders Enter Receiving Channel Position NumberReceived. Then press OK or Access G-CODE Showview Screen CODETimer ProgrammingReturn to Normal Timer ModeEngage Recorders Enter Programme Date Express Timer ProgrammingAccess Programme Enter Programme Stop TimeOr OK. Program Completed appears on Weekly TimerScreen for about 5 seconds, then normal screen Return to Timer Mode Disengage Timer ModeCheck, Cancel And Replace Programmes Auto Timer Auto SP→LP TimerAuto SP→LP Timer RE-SUPPLY Power Remote Control FunctionsRemove Power Supply SET Remote Control CodeTV Brand Name Code TV Multi-brand Remote ControlSET TV Brand Code Operate TVReturn to Normal Screen SET ModePreparation For Editing Picture ControlPlayer If the camcorder has no S-VIDEO output connector RecorderIf the camcorder has an S-VIDEO output connector Recorder Edit From CamcorderSynchro Editing Start Recording Deck SET Recording Decks Input ModeEdit To Or From Another Video Recorder Start Source PlayerLocate Start Point SET Input ModeAudio Dubbing Engage Audio DubbingEND Audio Dubbing Start DubbingPlay Stop Pause Insert Editing Reset the CounterLocate END Point END Insert Editing Start EditingRandom Assemble Editing Access R.A. Edit ScreenAudio signal Video signal CancelEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditAccess Jlip ID NO. SET Screen Access Initial SETTerminal JLIPJoint Level Interface Protocol Connector Audio Cable not provided Connecting Using a Stereo SystemOff-Air Recording Setting Of The Colour System Select ButtonsMode Display Mode DescriptionPlayback equipment Tape-To-Tape EditingDubbed tape Auto CH SET, then Auto Channel SetTuner SET, then press OK or Push JogþSET Desired Station Access Tuner SETAccess Channel List Select PositionSwap Channel Positions Delete a ChannelJOG% Push JOG Þ Fine-Tuning ChannelsPress Play to turn the indicator off Check the cassette If youre using the RF OUT connec- tionTimer again Timer record information has beenNew one. pg RoubleshootingQuest Ions and Answers Index Display Panel EN Index Maximum recording time Supplied fresh battery actualHR-S7600AM