JVC HR-S7850EU 34 EN, Enter the programme mode, Set the programme start/stop time and channel

Page 34

34 EN

TIMER RECORDING (cont.)

24 Hour Express Timer Programming

Before performing the 24 Hour Express Timer Programming:

●Make sure that the recorder’s built-in clock is set properly.

●Insert a cassette with the safety tab in place. The recorder will come on automatically.

●Set the tape speed.

You can programme a timer recording that starts within 24 hours using the JOG dial on the recorder.

A Enter the programme mode.

Press 24H EXPRESS # on the recorder. The start time indicator ( ) starts blinking on the front display panel.

●The current tape speed and VPS/PDC setting appears on the front display panel, but it is impossible to change the setting.

You can only change the setting after programming ( pg. 35).

NOTES:

●You can programme this recorder to timer-record as many as

8 programmes. If you try to programme the recorder to record a ninth, “FULL” appears on the front display panel. To record

the extra programme, you must first cancel any unnecessary programmes ( pg. 35).

●It is not possible to timer-record a satellite broadcast received on the channel position “0” by the satellite receiver.

●If “Err” appears on the front display panel, repeat the above steps again.

●When a menu screen is shown, you cannot use 24 Hour Express Timer Programming function. Press MENU to return to normal screen, and try again.

●You can use 24 Hour Express Timer Programming function also when the recorder is turned off.

●For 24 Hour Express Timer Programming function, the programme overlap warning display does not appear even if some programmes overlap each other. The programme with the lower programme number will be recorded and the other one will not be recorded correctly.

B Set the programme start/stop time and channel.

Turn the JOG dial to the left or right to set the time you want recording to start.

●One click stop of the JOG dial changes the time in 5-minute intervals.

Push the JOG dial. The stop time indicator ( ) starts blinking on the front display panel. Turn the JOG dial to the left or right to set the time you want recording to stop.

Push the JOG dial. Turn the JOG dial to the left or right to select the channel you wish to record.

●You can cancel the setting at any time by pressing and holding the JOG dial for more than 3 seconds or pressing & on the remote control. Repeat the step 2.

C Engage the recorder’s timer mode.

Press 24H EXPRESS #. The recorder turns off automatically and # appears on the front display panel.

●To disengage the timer mode, press # (TIMER) or 24H EXPRESS # again.

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Connector cover Front ViewRear View Front Display Panel ON-SCREEN Display Remote Control How To Use Operating JVC TVsSituate the recorder Check the contents10 EN Connect the recorder to TV8To connect to a TV with S-VIDEO/AUDIO in connectors Video ConnectionTurn on the recorder Auto Set Up12 EN Select your countryPress rt to select your language code Perform Auto Set UpSelect the language Press rt to select Auto and press OK or eSet the video channel Perform Preset Download14 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 16 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec Basic Playback 20 ENPause during playback Slow MotionHigh-Speed Turbo Search Activate frame-by-frame playbackIndex Search 22 ENVariable Speed Search Skip SearchManual Tracking Next Function MemoryRepeat Playback Soundtrack Selection24 EN Instant Timer Recording ITR Tape Remaining TimeRetake Engage the Record-Pause mode26 EN Locate the start pointEngage the S-VHS ET mode Receiving Stereo and Bilingual Programmes ReceivedPlayback RecordingBefore performing the Showview Timer Programming Access the Showview screenAccess the Showview Program screen 30 ENEngage the recorder’s timer mode Set the VPS/PDC modeAccess the Title Edit screen Enter the programme titleExpress Timer Programming 32 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR+34 EN Enter the programme modeBefore performing the 24 Hour Express Timer Programming Set the programme start/stop time and channelReturn to the timer mode Cancel or change a programmeDisengage the timer mode Access the Programme Check screen/displaySelect the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenProgramme Recording Select the L-2 Select modeRecording mode Before performing the following stepsNavigation 38 ENLoad a recorded cassette Navigation PlaybackProgramme Navigation Screen Select a programmeEdit Programme Title 40 ENSelect the programme Delete the tape data Entering CharacterDelete Tape Data Example Enter JVC NewsEdit From a Camcorder 42 ENAdvantages of S-VHS video recorders Set the input mode of recording deckAnother Video Recorder Start the source playerAccess the Output/Input Set screen 44 ENSelect and L-2 Input Setting Decoder connectorAudio Dubbing 46 ENEnd Audio Dubbing Engage the Audio Dubbing modeStart dubbing Press AUX number key 0 and/or PR to select F-1 or S-1Insert Editing 48 ENLocate the end point Engage the Insert Editing modeAV Insert Editing Start EditingConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Connect the decoder Select the input mode52 EN Set the tunerConnecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingDisengaged when the recorder is powered back on When viewing overplayedWhen this function is set to ON, the timer is automatically System to on or OFF  pg56 EN On the remote control, or press 7 on the recorderEntire programme while timer-recording in SP mode Function  pg , set PROG. Navigation to OFFWhen this function is set to ON, you can automatically When this function is set to ON, you can reducePower consumption while the recorder is turned off Correct vertical vibration in the picture when playing back58 EN About Ntsc PlaybackGuide Program Number Showview System SetupGuide Program Number Set Enter the Guide Program number60 EN Access the Auto Channel Set screenTuner Set Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice 62 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 64 ENSet Stations B TV Station And ID List Station NameClock Set Access the Clock Set screen66 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 68 ENPower 70 EN RecordingOther Problems 72 EN PlaybackScan system Signal-to-noise ratio 45 dB Horizontal resolutionMemory backup time Approx min Lines VHS74 EN Memo International telephone Language code Country code
Top Page Image Contents