JVC HR-S7851EU, HR-S7850EU specifications Other Problems

Page 71

			EN 71

	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
6.	“[” on the front display panel and	● The loaded cassette has had its record	Remove the cassette and cover the hole
	SAT # indicator won’t stop blinking.	safety tab removed.	with adhesive tape, or insert a cassette
			with the record safety tab intact.
		● The end of the tape was reached during	The programme may not have been
		Automatic Satellite Programme	recorded in its entirety. Next time make
		Recording.	sure you have enough time on the tape to
			record the entire programme.

7.	The power shuts off and “[” won’t	● The end of the tape was reached during	The programme may not have been
	stop blinking.	Instant Timer Recording.	recorded in its entirety. Next time make
			sure you have enough time on the tape to
			record the entire programme.

OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1. Whistling or howling is heard from the		● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 62).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			Then perform Auto Set Up again
			( pg. 12).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 14).

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 71

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Front Display Panel ON-SCREEN Display Remote Control Operating JVC TVs How To UseConnect the recorder to TV Check the contents10 EN Situate the recorderVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsSelect your country Auto Set Up12 EN Turn on the recorderPress rt to select Auto and press OK or e Perform Auto Set UpSelect the language Press rt to select your language codePress rt to select CH - and press OK or e Perform Preset Download14 EN Set the video channelJust Clock Language for the on-screen display16 EN Access the Main Menu screenAccess the Country Set screen LanguageMake connections Installing Satellite ControllerSituate the Satellite Controller Attach the Satellite Controller18 EN Setting satellite receivers brand and channelVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link 20 EN Basic PlaybackActivate frame-by-frame playback Slow MotionHigh-Speed Turbo Search Pause during playbackSkip Search 22 ENVariable Speed Search Index SearchSoundtrack Selection Next Function MemoryRepeat Playback Manual Tracking24 EN Tape Remaining Time Instant Timer Recording ITRLocate the start point Engage the Record-Pause mode26 EN RetakeEngage the S-VHS ET mode Received Receiving Stereo and Bilingual ProgrammesRecording Playback30 EN Access the Showview screenAccess the Showview Program screen Before performing the Showview Timer ProgrammingEnter the programme title Set the VPS/PDC modeAccess the Title Edit screen Engage the recorder’s timer mode32 EN Express Timer ProgrammingPress PR+ To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel positionSet the programme start/stop time and channel Enter the programme modeBefore performing the 24 Hour Express Timer Programming 34 ENAccess the Programme Check screen/display Cancel or change a programmeDisengage the timer mode Return to the timer modeOverlapping programmes blink on the TV screen Cancel or change programme settingConfirm the overlapping programmes Select the programme to modifyBefore performing the following steps Select the L-2 Select modeRecording mode Programme Recording38 EN NavigationSelect a programme Navigation PlaybackProgramme Navigation Screen Load a recorded cassetteSelect the programme 40 ENEdit Programme Title Example Enter JVC News Entering CharacterDelete Tape Data Delete the tape data42 EN Edit From a CamcorderStart the source player Set the input mode of recording deckAnother Video Recorder Advantages of S-VHS video recorders44 EN Access the Output/Input Set screenDecoder connector Select and L-2 Input Setting46 EN Audio DubbingPress AUX number key 0 and/or PR to select F-1 or S-1 Engage the Audio Dubbing modeStart dubbing End Audio Dubbing48 EN Insert EditingStart Editing Engage the Insert Editing modeAV Insert Editing Locate the end pointSimple Connections Connecting To a Satellite ReceiverPerfect Connections Set the tuner Select the input mode52 EN Connect the decoderMake connections Connecting/Using a Stereo SystemSelect the mode setting Mode SetAccess the Mode Set screen Select the modeSystem to on or OFF pg When viewing overplayedWhen this function is set to ON, the timer is automatically Disengaged when the recorder is powered back onFunction pg , set PROG. Navigation to OFF On the remote control, or press 7 on the recorderEntire programme while timer-recording in SP mode 56 ENCorrect vertical vibration in the picture when playing back When this function is set to ON, you can reducePower consumption while the recorder is turned off When this function is set to ON, you can automaticallyAbout Ntsc Playback 58 ENEnter the Guide Program number Showview System SetupGuide Program Number Set Guide Program NumberAuto Channel Set Access the Auto Channel Set screenTuner Set 60 ENPress OK twice Perform Auto Channel SetView the Confirmation screen Manual Channel Set 62 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations B 64 ENSet Stations a Station Name TV Station And ID List66 EN Access the Clock Set screenClock Set Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock data68 EN Access the Video Channel Set modeExit the Video Channel Set mode Video Channel SetPower Recording 70 ENOther Problems Playback 72 ENLines VHS Signal-to-noise ratio 45 dB Horizontal resolutionMemory backup time Approx min Scan system74 EN Memo Country code International telephone Language code