JVC HR-S7851EU, HR-S7850EU specifications Select and L-2 Input Setting, Decoder connector

Page 45

EN 45

L-2 SELECT and L-2 INPUT Setting

The AV2 (L-2) IN/DECODER connector accepts either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set “L-2 SELECT” to the appropriate mode depending on the type of appliance connected to the recorder’s AV2 (L-2) IN/ DECODER connector. Set “L-2 INPUT” to the appropriate mode depending on the output signals of the connected appliance.

Perform steps 1 and 2 of “L-1 OUTPUT and L-1 INPUT Setting” on page 44.

A Select the input mode for the AV2 (L-2) IN/

DECODER connector.

Press rt to move the highlight bar (pointer) to “L-2 SELECT” or “L-2 INPUT”. Then, press OK or e to select the appropriate setting.

*The default setting is bold in the table below.

8L-2 SELECT

A/V: To use this recorder as the recording deck with the player connected to the AV2 (L-2) IN/DECODER connector, or to use the satellite receiver connected to the AV2 (L-2) IN/DECODER connector.

DECODER: To use a decoder connected to the AV2 (L-2) IN/DECODER connector.

SAT: To view a satellite programme with the TV set while the recorder is turned off. ( pg. 50)

8L-2 INPUT

VIDEO: If a connected appliance’s output is compatible only with regular video signals, set to “VIDEO”.

S-VIDEO: If a connected appliance’s output is compatible with Y/C signals, set to “S-VIDEO”. You can obtain high-quality S-VHS picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

B Return to the normal screen.

NOTES:

●If you have a satellite receiver or a decoder connected to the AV2 (L-2) IN/DECODER connector, be sure to set “L-2 SELECT” back to appropriate mode after editing.

●If you are not connecting a satellite receiver or a decoder to the AV2 (L-2) IN/DECODER connector, leave “L-2 SELECT” set to “A/V”.

●The default setting is “A/V”; if the recorder’s memory backup has expired due to a power cut or because the AC was removed from the recorder, “A/V” will be automatically selected when the power is restored to the recorder. If you are using a satellite receiver or a decoder, be sure to set “L-2 SELECT” back to appropriate mode.

●When “L-2 SELECT” is set to “SAT”, “SAT” appears on TV screen or front display panel instead of “L-2” or “L2”.

●If “L-2 SELECT” is set to “DECODER”, it is impossible to set “L-2 INPUT” to “S-VIDEO”.

●If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set “L-2 SELECT” to “DECODER”.

Press MENU.

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Front Display Panel ON-SCREEN Display Remote Control Operating JVC TVs How To Use10 EN Check the contentsSituate the recorder Connect the recorder to TVVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectors12 EN Auto Set UpTurn on the recorder Select your countrySelect the language Perform Auto Set UpPress rt to select your language code Press rt to select Auto and press OK or e14 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 16 ENSituate the Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connections18 EN Setting satellite receivers brand and channelTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec 20 EN Basic PlaybackHigh-Speed Turbo Search Slow MotionPause during playback Activate frame-by-frame playbackVariable Speed Search 22 ENIndex Search Skip SearchRepeat Playback Next Function MemoryManual Tracking Soundtrack Selection24 EN Tape Remaining Time Instant Timer Recording ITR26 EN Engage the Record-Pause modeRetake Locate the start pointEngage the S-VHS ET mode Received Receiving Stereo and Bilingual ProgrammesRecording PlaybackAccess the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 30 ENAccess the Title Edit screen Set the VPS/PDC modeEngage the recorder’s timer mode Enter the programme title32 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Before performing the 24 Hour Express Timer Programming Enter the programme mode34 EN Set the programme start/stop time and channelDisengage the timer mode Cancel or change a programmeReturn to the timer mode Access the Programme Check screen/displayConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Overlapping programmes blink on the TV screenRecording mode Select the L-2 Select modeProgramme Recording Before performing the following steps38 EN NavigationProgramme Navigation Screen Navigation PlaybackLoad a recorded cassette Select a programme40 EN Edit Programme TitleSelect the programme Delete Tape Data Entering CharacterDelete the tape data Example Enter JVC News42 EN Edit From a CamcorderAnother Video Recorder Set the input mode of recording deckAdvantages of S-VHS video recorders Start the source player44 EN Access the Output/Input Set screenDecoder connector Select and L-2 Input Setting46 EN Audio DubbingStart dubbing Engage the Audio Dubbing modeEnd Audio Dubbing Press AUX number key 0 and/or PR to select F-1 or S-148 EN Insert EditingAV Insert Editing Engage the Insert Editing modeLocate the end point Start EditingSimple Connections Connecting To a Satellite ReceiverPerfect Connections 52 EN Select the input modeConnect the decoder Set the tunerMake connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingWhen this function is set to ON, the timer is automatically When viewing overplayedDisengaged when the recorder is powered back on System to on or OFF  pgEntire programme while timer-recording in SP mode On the remote control, or press 7 on the recorder56 EN Function  pg , set PROG. Navigation to OFFPower consumption while the recorder is turned off When this function is set to ON, you can reduceWhen this function is set to ON, you can automatically Correct vertical vibration in the picture when playing backAbout Ntsc Playback 58 ENGuide Program Number Set Showview System SetupGuide Program Number Enter the Guide Program numberTuner Set Access the Auto Channel Set screen60 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice Manual Channel Set 62 ENDelete a Channel When Receiving a Scrambled Broadcast64 EN Set Stations aSet Stations B Station Name TV Station And ID ListAccess the Clock Set screen Clock Set66 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operationExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 68 ENPower Recording 70 ENOther Problems Playback 72 ENMemory backup time Approx min Signal-to-noise ratio 45 dB Horizontal resolutionScan system Lines VHS74 EN Memo Country code International telephone Language code
Top Page Image Contents