JVC HR-S7850EU 10 EN, Check the contents, Situate the recorder, Connect the recorder to TV

Page 10

10 EN

INSTALLING YOUR NEW RECORDER

Basic Connections

Aerial connector

Back of TV

21-pin SCART

TV aerial

connector

cable

 

21-pin SCART

RF cable

cable

(provided)

(not provided)

 

Mains power cord

ANT. IN

Back of recorder

AV1 (L-1) IN/OUT RF OUT

Mains outlet

Make AV connection if your TV has a 21-pin AV input connector (SCART) in order to reduce the possibility of interference. With AV connection, you can enjoy stereo playback of video tapes if you are using a stereo TV.

NOTES:

●The AV1 (L-1) IN/OUT connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). If your TV’s 21-pin AV input connector (SCART) is compatible with the Y/C signal, set

“L-1 OUTPUT” to “S-VIDEO” after the connection and the initial settings are completed ( pg. 44). You can obtain high-quality S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

●Set your TV to the VIDEO (or AV), Y/C, or RGB mode according to the type of your TV’s SCART connector.

●For switching the TV’s mode, refer to the instruction manual of your television.

●To obtain high-quality S-VHS pictures, you can also use the S-VIDEO connection described on page 11.

It’s essential that your video recorder be properly connected.

THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

A Check the contents.

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” on page 73.

B Situate the recorder.

Place the recorder on a stable, horizontal surface.

C Connect the recorder to TV.

The connection method you use depends on the type of TV you have.

RF Connection

8To connect to a TV with NO AV input connectors . . .

ADisconnect the TV aerial cable from the TV.

BConnect the TV aerial cable to the ANT. IN connector on the rear panel of the recorder.

CConnect the provided RF cable between the RF OUT connector on the rear panel of the recorder and the TV’s aerial connector.

AV Connection

8To connect to a TV with AV input connectors . . .

AConnect the aerial, recorder and TV as per “RF Connection”.

BConnect an optional 21-pin SCART cable between the AV1 (L-1) IN/OUT connector on the rear panel of the recorder and the TV’s 21-pin SCART connector.

D Connect the recorder to mains.

Plug the end of the mains power cord into a mains outlet.

After the connection is completed, perform “Auto Set Up” on page 12.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Connector cover Front ViewRear View Front Display Panel ON-SCREEN Display Remote Control How To Use Operating JVC TVsSituate the recorder Check the contents10 EN Connect the recorder to TV8To connect to a TV with S-VIDEO/AUDIO in connectors Video ConnectionTurn on the recorder Auto Set Up12 EN Select your countryPress rt to select your language code Perform Auto Set UpSelect the language Press rt to select Auto and press OK or eSet the video channel Perform Preset Download14 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 16 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec Basic Playback 20 ENPause during playback Slow MotionHigh-Speed Turbo Search Activate frame-by-frame playbackIndex Search 22 ENVariable Speed Search Skip SearchManual Tracking Next Function MemoryRepeat Playback Soundtrack Selection24 EN Instant Timer Recording ITR Tape Remaining TimeRetake Engage the Record-Pause mode26 EN Locate the start pointEngage the S-VHS ET mode Receiving Stereo and Bilingual Programmes ReceivedPlayback RecordingBefore performing the Showview Timer Programming Access the Showview screenAccess the Showview Program screen 30 ENEngage the recorder’s timer mode Set the VPS/PDC modeAccess the Title Edit screen Enter the programme titleExpress Timer Programming 32 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR+34 EN Enter the programme modeBefore performing the 24 Hour Express Timer Programming Set the programme start/stop time and channelReturn to the timer mode Cancel or change a programmeDisengage the timer mode Access the Programme Check screen/displaySelect the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenProgramme Recording Select the L-2 Select modeRecording mode Before performing the following stepsNavigation 38 ENLoad a recorded cassette Navigation PlaybackProgramme Navigation Screen Select a programmeEdit Programme Title 40 ENSelect the programme Delete the tape data Entering CharacterDelete Tape Data Example Enter JVC NewsEdit From a Camcorder 42 ENAdvantages of S-VHS video recorders Set the input mode of recording deckAnother Video Recorder Start the source playerAccess the Output/Input Set screen 44 ENSelect and L-2 Input Setting Decoder connectorAudio Dubbing 46 ENEnd Audio Dubbing Engage the Audio Dubbing modeStart dubbing Press AUX number key 0 and/or PR to select F-1 or S-1Insert Editing 48 ENLocate the end point Engage the Insert Editing modeAV Insert Editing Start EditingConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Connect the decoder Select the input mode52 EN Set the tunerConnecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingDisengaged when the recorder is powered back on When viewing overplayedWhen this function is set to ON, the timer is automatically System to on or OFF  pg56 EN On the remote control, or press 7 on the recorderEntire programme while timer-recording in SP mode Function  pg , set PROG. Navigation to OFFWhen this function is set to ON, you can automatically When this function is set to ON, you can reducePower consumption while the recorder is turned off Correct vertical vibration in the picture when playing back58 EN About Ntsc PlaybackGuide Program Number Showview System SetupGuide Program Number Set Enter the Guide Program number60 EN Access the Auto Channel Set screenTuner Set Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice 62 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 64 ENSet Stations B TV Station And ID List Station NameClock Set Access the Clock Set screen66 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 68 ENPower 70 EN RecordingOther Problems 72 EN PlaybackScan system Signal-to-noise ratio 45 dB Horizontal resolutionMemory backup time Approx min Lines VHS74 EN Memo International telephone Language code Country code
Top Page Image Contents