JVC HR-S7851EU AV Insert Editing, Locate the end point, Engage the Insert Editing mode

Page 49

EN 49

A Make connections.

Connect the player’s VIDEO OUT or S-VIDEO OUT and AUDIO OUT connectors to your recorder’s VIDEO or S-VIDEO and AUDIO input connectors on the front panel.

B Set the recorder’s input mode.

Press AUX (number key “0”) and/or PR to select “F-1” for the AUDIO and VIDEO input connectors or “S-1” for AUDIO and S-VIDEO input connectors.

C Locate the end point.

Load the recording cassette into your recorder, and play it back to determine the edit-out point (the end of the segment to be replaced) using the JOG dial, or pressing w

eand 9.

D Reset the counter.

Press 0000.

●The counter is reset to “0:00:00”.

E Locate the start point.

Determine the edit-in point (the beginning of the segment to be replaced) using the JOG dial, or pressing w e and

9.

●Be sure to engage the Still mode at the edit-in point.

F Engage the Insert Editing mode.

Press INSERT.

●Your recorder enters the Insert Pause mode. (“o”, “u” and “i” light up on the front display panel.)

●The TV screen changes from the still picture to the input source you are going to record.

G Start Editing.

Load the source cassette and play back the segment that is to be inserted. When you reach the start of the section of the source tape that you wish to insert, press 4 to start the tape in your recorder; Insert Editing begins at this point.

●“o” and “u” are displayed on the front display panel.

H End Insert Editing.

At counter “0:00:00”, Insert Editing will stop automatically while the tape continues running in the Play mode. If you wish to stop Insert Editing before the specified edit-out point, press 0000.

AV Insert Editing

If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time ...

... In step 6, after you press INSERT, press A.DUB also.

(“o” and “u” blink and “i” lights up on the front display panel.)

NOTES:

●All necessary cables can be obtained from your dealer.

●Insert Editing is not possible with cassettes whose record safety tab has been removed.

●When Insert Editing is performed on a tape that has been recorded on another video recorder, the inserted portion may appear distorted.

●In Insert Editing, the recording speed (SP/LP) is determined by the previous recording to be replaced. If the previous recording’s speed changes within a single edit, the inserted picture will be distorted at the switching point.

●A small portion of the recording which precedes an insert edit may become erased.

●Insert Editing is also possible using the rear panel AV1 (L-1) IN/ OUT or AV2 (L-2) IN/DECODER connector. When using these 21-pin SCART connectors, be sure to select the correct input mode (“L-1” or “L-2”) in step 2.

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Front Display Panel ON-SCREEN Display Remote Control Operating JVC TVs How To Use10 EN Check the contentsSituate the recorder Connect the recorder to TVVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectors12 EN Auto Set UpTurn on the recorder Select your countrySelect the language Perform Auto Set UpPress rt to select your language code Press rt to select Auto and press OK or e14 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 16 ENSituate the Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connections18 EN Setting satellite receivers brand and channelNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec 20 EN Basic PlaybackHigh-Speed Turbo Search Slow MotionPause during playback Activate frame-by-frame playbackVariable Speed Search 22 ENIndex Search Skip SearchRepeat Playback Next Function MemoryManual Tracking Soundtrack Selection24 EN Tape Remaining Time Instant Timer Recording ITR26 EN Engage the Record-Pause modeRetake Locate the start pointEngage the S-VHS ET mode Received Receiving Stereo and Bilingual ProgrammesRecording PlaybackAccess the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 30 ENAccess the Title Edit screen Set the VPS/PDC modeEngage the recorder’s timer mode Enter the programme title32 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Before performing the 24 Hour Express Timer Programming Enter the programme mode34 EN Set the programme start/stop time and channelDisengage the timer mode Cancel or change a programmeReturn to the timer mode Access the Programme Check screen/displayConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Overlapping programmes blink on the TV screenRecording mode Select the L-2 Select modeProgramme Recording Before performing the following steps38 EN NavigationProgramme Navigation Screen Navigation PlaybackLoad a recorded cassette Select a programmeEdit Programme Title 40 ENSelect the programme Delete Tape Data Entering CharacterDelete the tape data Example Enter JVC News42 EN Edit From a CamcorderAnother Video Recorder Set the input mode of recording deckAdvantages of S-VHS video recorders Start the source player44 EN Access the Output/Input Set screenDecoder connector Select and L-2 Input Setting46 EN Audio DubbingStart dubbing Engage the Audio Dubbing modeEnd Audio Dubbing Press AUX number key 0 and/or PR to select F-1 or S-148 EN Insert EditingAV Insert Editing Engage the Insert Editing modeLocate the end point Start EditingSimple Connections Connecting To a Satellite ReceiverPerfect Connections 52 EN Select the input modeConnect the decoder Set the tunerMake connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingWhen this function is set to ON, the timer is automatically When viewing overplayedDisengaged when the recorder is powered back on System to on or OFF  pgEntire programme while timer-recording in SP mode On the remote control, or press 7 on the recorder56 EN Function  pg , set PROG. Navigation to OFFPower consumption while the recorder is turned off When this function is set to ON, you can reduceWhen this function is set to ON, you can automatically Correct vertical vibration in the picture when playing backAbout Ntsc Playback 58 ENGuide Program Number Set Showview System SetupGuide Program Number Enter the Guide Program numberTuner Set Access the Auto Channel Set screen60 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice Manual Channel Set 62 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations a 64 ENSet Stations B Station Name TV Station And ID ListClock Set Access the Clock Set screen66 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operationExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 68 ENPower Recording 70 ENOther Problems Playback 72 ENMemory backup time Approx min Signal-to-noise ratio 45 dB Horizontal resolutionScan system Lines VHS74 EN Memo Country code International telephone Language code
Top Page Image Contents