JVC HR-S7600U Cable Box Control, Situate Controller, Attach Controller, Connect Cable BOX to VCR

Page 16

16ENINITIALSETTINGS(cont.)

Cable Box

Control

Suggested Location

Place the cable box on top of the VCR. Attach the VCR's Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.

ATTENTION:

The Controller can also control a DBS receiver. If both a cable box and a DBS receiver are used, position the controller so its signal reaches the remote control sensors of both the cable box and DBS receiver.

Cable box

Your VCR

Controller

(suggested locations)

 

 

Cable box

 

 

 

 

 

 

Controller

Transmitter

 

 

 

 

Audio/Video

Connected to

 

cable

 

(supplied)

ANTENNA IN

Your VCR

CABLE

BOX

This procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the VCR to automatically switch the cable box channel during timer-recording. The Controller is effective for recording shows that have been programmed using VCR Plus+ (☞ pg. 45) or Express Timer Programming (☞ pg. 49).

Situate And Connect

Controller

SITUATE CONTROLLER

1 Place the Controller so that the path between its transmitter and the cable box’s remote sensor is unobstructed.

ATTACH CONTROLLER

2 Fasten securely using the supplied adhesive strip.

CONNECT CABLE BOX TO VCR

3 The connection method depends on the type of cable box you have.

If your cable box has AUDIO and VIDEO OUT connectors . . .

. . . connect them to the AUDIO and VIDEO IN connectors on your VCR. Set the VCR to channel "L-1" for the rear AUDIO and VIDEO IN connectors, or channel "F-1" for the front AUDIO and VIDEO IN connectors to use the cable box.

If your cable box doesn’t have AUDIO and VIDEO OUT connectors . . .

. . . connect the antenna output connector on the cable box to the ANTENNA IN connector on the rear of your VCR.

Set the VCR tuner to the same channel as the cable box RF output (see page 17 also).

NOTE:

When connecting your cable box refer to its instruction manual.

CONNECT CONTROLLER TO VCR

4 Connect to the CABLE BOX connector on your VCR.

About Your Cable Box

This VCR has two separate methods to control your Cable Box.

●The VCR's Wireless Remote Control Unit can control your Cable Box.

This eliminates the need for a separate Cable Box Remote Control Unit.

●The VCR's Controller can also control your Cable Box.

This allows the VCR to change your Cable Box's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 62. To set up the Controller go to page 17.

HR-S7600U-EN01-23

16

99.4.28, 2:01 PM

Page 15 Page 17
Image 16
Page 15 Page 17
Contents HR-S7600U Dear Customer Do not place the VCRInstallation Antenna Installation InstructionsUSE Before YOU Install Your NEW VCRServicing Contents Connections Back of VCR Video CableRF Cable supplied Connect VCR to TVPlug & Play Setup Plug & PlayEN I Nitial Sett Ings Auto Clock Set/Auto Tuner SetInformation Language Access Clock SET ClockPreparation Scan #Select D.S.T. Mode SET Auto Clock to onSelect Host Channel Semi-AutoSelect Time Zone Return to Normal ScreenSET Time SET DateAccess Main Menu Screen Access Tuner SET ScreenTuner SETAccess Manual ChannelAdd Or Delete a Channel Time Scan #Cable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCRAccess Cable BOX SET Turn on Cable BOXSelect Cable BOX Output ChannelAccess Cable BOX Brand SET Screen Initial SettingsEnter Cable BOX Brand MenuConnect DBS Receiver To VCR DBS Receiver ControlDBS receiver Access Initial SET Screen Access DBS Receiver SET ScreenTurn on DBS Receiver Set DBS Receiver Output Channel & DBS Receiver BrandAccess DBS Receiver SET DBS Receiver BrandSimple Playback Simple Recording Playback Features Activate FRAME-BYFrame Playback Still Picture/Frame-By- Frame PlaybackAccess Distant Code Engage Manual Tracking ModeAdjust Manual Tracking Start SearchAccess Function SET Screen Select Picture Control SET ModeLayback and Recording Features Picture ControlSelect The Soundtrack Video StabilizerStart Repeat Stop RepeatAccess Function SET ModeSuperimpose Select Superimpose SETAccess Main Menu Screen AV Compu Link PlaybackMake Connection ExampleAccess Skip Menu Select ModePerform Movie AdvanceCommercial Advance Commercial Advance works as followsSelect CA Playback SET Mode Return to Normal ScreenPress CH 5 or Time CA RECORD, then pressAudio signal during TimeScan Time ScanVariable-Speed Search/ Reverse Motion Playback Playback tape 1 2 3 4Skip Over Unwanted Sections Skip SearchSpeed Audio output Pro-SlowON/OFF as required Default setting is on TimeScan AudioTimescan AUDIO, then To set to on or OFFDigital TBC/NR SET ModeDigital R3 Active Video Calibration Video CalibrationRecording PlaybackStart Playback Recording Features VHS Super VHS, S-VHS ET and VHS Select S-VHS ET SET Mode Super VHS ETPress S-VHS ET. The button lights up PanelStereo And SAP Second Audio Program To Record SAP ProgramsTo move the on-screens audio levels by one VCR Plus+ Timer Programming Timer RecordingNumber Enter Pluscode NumberEN Timer Recording Engage Timer ModeCheck Program Data VCR Plus+ Setup VCR Plus+ Guide Channel MatchingInitial SET, then press OK or Time Scan #Access Guide Channel SET Screen Input Guide Channel NumberInput Receiving Channel Number Press CH5, Time ScanSET Program Date Express Timer ProgrammingSET Channel Number If you are using a DBS receiver Press SP/EP to set the tape speedUnless DBS Receiver SET is Set to OFF pg , Band indication TV or CatvCancel or Revise a Program RE-ENGAGE TimerCheck, Cancel And Revise ProgramsSelect Auto SP=EP Timer SET Mode Auto SP=EP TimerAuto Timer Or Time Scan %ÞInstant Timer Recording ITR Engage ITR ModeSET Recording Duration Press REC on the front panelAutomatic Sat- ellite Program Recording Engage Auto Satellite Prog REC ModeBefore performing the following steps Edit To Or From Another Edit From a Camcorder EditingEnable Remote Pause Function Return to Normal Screen Set your VCR to its record modeStart Player Start RecorderReset the Counter Insert EditingLocate END Point Locate Start PointStart Editing Engage Insert EditingEND Insert Editing SET RECORDER’S Input Mode Audio DubbingEngage Audio Dubbing Start DubbingSpeci AL Features EN TV Multi-Brand Remote ControlTurn on the TV SET TV Brand CodeEN Special Features Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXDBS Receiver Multi-Brand Remote Control Turn on the DBS ReceiverEnter DBS Receiver Brand Operate DBS ReceiverUnplug Vcrs Power SET Remote ControlPlug in Power Cord Turn VCR Power onCassette gets stuck partway Troubleshooting ENMake sure the cassettes window is Timer again RoubleshootingOther Problems When scanning channels, someCan the VCR indefinitely remain in the Record-Pause mode? Can the VCR indefinitely remain in the still mode?What happens if the tape runs out during recording? MBR Multi-Brand Remote Code Setting VCR Plus+ Timer ProgrammingIndex List Of TermsFront View Rear View Remote Control EN IndexSpeci Fications Video connectors in x 2, OUT x20C to 60C -4F to140F HOW to Locate Your JVC Service Center Limited Warranty HR-S7600U
Top Page Image Contents