JVC HR-S7600U manual Commercial Advance works as follows

Page 32
MARKING COMMERCIALS

32EN

PLAYBACKANDRECORDINGFEATURES(cont.)

Commercial Advance

Your VCR is equipped with the Commercial Advance feature, which can automatically fast-motion the tape during playback to skip over previously recorded TV commercials.

Commercial Advance works as follows:

1When recording is finished, the following display will appear on the screen and the VCR's front display panel.

MARKING COMMERCIALS

WILL BE EXECUTED.

 

* In case of timer recording, these

 

displays will appear when all the preset

 

programs are recorded. If you press

PRESS (OK) TO START

TIMER to disengage the timer mode,

PRESS (STOP) TO CANCEL

these displays will appear even if all

 

the programs are not recorded yet.

NOTE:

Commercials can only be marked if Commercial Advance Record is enabled (☞ pg. 33).

a– Press OK and step 2 will take place.

b– If you do not want to use Commercial Advance for the recorded program, press STOP.

c– If neither button is pressed within 60 seconds after the displays appear, step 2 will take place automatically.

IMPORTANT

If you press STOP in this step or stop marking midway in step

2before the VCR is finished marking the commercials, data

necessary for Commercial Advance will be lost and this feature will not work with the recording you made.

2The VCR rewinds the tape automatically to the beginning of the recording and seeks out the commercial groups which have been detected.

During search and marking

Search and marking

Program

Commercial Commercial Commercial

Program

*If you want to stop marking midway, press STOP so that "MARKING IN PROCESS" appears on the screen and "CA" blinks on the front display panel. While those are displayed (for 5 seconds), press STOP again to cancel

Commercial Advance marking of the rest of the recordings.

*If you want to watch a TV program while the VCR is marking commercials, first press TV/VCR on the remote control, then use the TV's channel selector to select the channel you want to watch.

 

 

Commercial group

 

 

MARK

MARK

 

After having marked the start and end of all commercial groups of the recording(s), the VCR goes to its Stop mode. In the case of timer recording or Instant Timer Recording, the VCR shuts off automatically.

3During playback, the VCR automatically (when enabled ☞ pg. 33) fast-motions (with blueback screen) during the commercial groups that were marked in step 2.

* When Commercial Advance is forwarding the tape to skip over commercials, "CA SKIP" will be displayed in the top right corner of the TV screen.

Playback

 

Forward fast-motion playback

Playback

 

(with blueback screen)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Program

 

Commercial

Commercial

Commercial

Program

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Commercial group

 

 

 

 

 

 

 

MARK

MARK

 

 

 

 

NOTES:

●The Commercial Advance Record processes marks the tape when the picture fades to black and the audio fades to silence. Normally there is a period of black and no audio at the beginning and end of commercials.

●A black screen or a scene with no audio signal during a program may be detected as the start or end of a commercial.

●When using the timer to record two adjacent shows on the same channel, better commercial detection accuracy can be obtained by programming each show separately.

●If you record over a commercial start or end mark the Commercial Advance feature will not work correctly.

●Commercial Advance tested with 6 hours recordings, longer recordings may be possible depending on the number of commercials contained in the broadcast.

●The VCR will resume normal playback after skipping 15 minutes of tape if no commercial group end mark is detected.

●If the end of the tape is reached during recording, the display as illustrated in step 1 appears, then...

•in the case of timer recording or Instant Timer Recording, after step 2 takes place, the cassette will be ejected and the power will shut off.

•in the case of normal recording, after step 2 takes place, the VCR will rewind to the beginning of the tape.

●During automatic commercial skipping, if the user presses STOP or PLAY, the VCR will resume normal play; furthermore, if the tape is reversed to before the commercial group and played, the commercial group will not automatically be skipped.

●If an index code or the end of a recording is detected during Commercial Advance's forward fast-motion playback, normal playback resumes automatically.

●Commercial Advance disables commercial marking when the recording is less than 15 minutes.

●Commercial Advance does not mark the start of a commercial group when it is in the first or last two minutes of a recording.

●Commercial Advance does not mark commercial groups which are less than 59 seconds or groups which contain only one commercial.

●Some portions of programs may be detected as commercials.

●Some commercials may not be detected properly.

HR-S7600U-EN24-44

32

99.4.28, 2:03 PM

Page 31 Page 33
Image 32
Page 31 Page 33
Contents HR-S7600U Dear Customer Do not place the VCRInstallation Antenna Installation InstructionsServicing Before YOU Install Your NEW VCRUSE Contents Connections Back of VCR Video CableRF Cable supplied Connect VCR to TVPlug & Play Setup Plug & PlayEN I Nitial Sett Ings Auto Clock Set/Auto Tuner SetInformation Language Access Clock SET ClockPreparation Scan #Select D.S.T. Mode SET Auto Clock to onSelect Host Channel Semi-AutoSelect Time Zone Return to Normal ScreenSET Time SET DateAccess Main Menu Screen Access Tuner SET ScreenTuner SETAccess Manual ChannelAdd Or Delete a Channel Time Scan #Cable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCRAccess Cable BOX SET Turn on Cable BOXSelect Cable BOX Output ChannelAccess Cable BOX Brand SET Screen Initial SettingsEnter Cable BOX Brand MenuDBS receiver DBS Receiver ControlConnect DBS Receiver To VCR Access Initial SET Screen Access DBS Receiver SET ScreenTurn on DBS Receiver Set DBS Receiver Output Channel & DBS Receiver BrandAccess DBS Receiver SET DBS Receiver BrandSimple Playback Simple Recording Playback Features Activate FRAME-BYFrame Playback Still Picture/Frame-By- Frame PlaybackAccess Distant Code Engage Manual Tracking ModeAdjust Manual Tracking Start SearchAccess Function SET Screen Select Picture Control SET ModeLayback and Recording Features Picture ControlSelect The Soundtrack Video StabilizerStart Repeat Stop RepeatAccess Function SET ModeSuperimpose Select Superimpose SETAccess Main Menu Screen AV Compu Link PlaybackMake Connection ExampleAccess Skip Menu Select ModePerform Movie AdvanceCommercial Advance Commercial Advance works as followsSelect CA Playback SET Mode Return to Normal ScreenPress CH 5 or Time CA RECORD, then pressAudio signal during TimeScan Time ScanVariable-Speed Search/ Reverse Motion Playback Playback tape 1 2 3 4Skip Over Unwanted Sections Skip SearchSpeed Audio output Pro-SlowON/OFF as required Default setting is on TimeScan AudioTimescan AUDIO, then To set to on or OFFDigital R3 SET ModeDigital TBC/NR Active Video Calibration Video CalibrationStart Playback PlaybackRecording Recording Features VHS Super VHS, S-VHS ET and VHS Select S-VHS ET SET Mode Super VHS ETPress S-VHS ET. The button lights up PanelStereo And SAP Second Audio Program To Record SAP ProgramsTo move the on-screens audio levels by one VCR Plus+ Timer Programming Timer RecordingNumber Enter Pluscode NumberCheck Program Data Engage Timer ModeEN Timer Recording VCR Plus+ Setup VCR Plus+ Guide Channel MatchingInitial SET, then press OK or Time Scan #Access Guide Channel SET Screen Input Guide Channel NumberInput Receiving Channel Number Press CH5, Time ScanSET Channel Number Express Timer ProgrammingSET Program Date If you are using a DBS receiver Press SP/EP to set the tape speedUnless DBS Receiver SET is Set to OFF pg , Band indication TV or CatvCancel or Revise a Program RE-ENGAGE TimerCheck, Cancel And Revise ProgramsSelect Auto SP=EP Timer SET Mode Auto SP=EP TimerAuto Timer Or Time Scan %ÞInstant Timer Recording ITR Engage ITR ModeSET Recording Duration Press REC on the front panelBefore performing the following steps Engage Auto Satellite Prog REC ModeAutomatic Sat- ellite Program Recording Edit To Or From Another Edit From a Camcorder EditingEnable Remote Pause Function Return to Normal Screen Set your VCR to its record modeStart Player Start RecorderReset the Counter Insert EditingLocate END Point Locate Start PointEND Insert Editing Engage Insert EditingStart Editing SET RECORDER’S Input Mode Audio DubbingEngage Audio Dubbing Start DubbingSpeci AL Features EN TV Multi-Brand Remote ControlTurn on the TV SET TV Brand CodeEN Special Features Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXDBS Receiver Multi-Brand Remote Control Turn on the DBS ReceiverEnter DBS Receiver Brand Operate DBS ReceiverUnplug Vcrs Power SET Remote ControlPlug in Power Cord Turn VCR Power onMake sure the cassettes window is Troubleshooting ENCassette gets stuck partway Timer again RoubleshootingOther Problems When scanning channels, someWhat happens if the tape runs out during recording? Can the VCR indefinitely remain in the still mode?Can the VCR indefinitely remain in the Record-Pause mode? MBR Multi-Brand Remote Code Setting VCR Plus+ Timer ProgrammingIndex List Of TermsFront View Rear View Remote Control EN Index20C to 60C -4F to140F Video connectors in x 2, OUT xSpeci Fications HOW to Locate Your JVC Service Center Limited Warranty HR-S7600U
Top Page Image Contents