JVC HR-S7600U manual Automatic Sat- ellite Program Recording, Engage Auto Satellite Prog REC Mode

Page 54

54ENTIMERRECORDING(cont.)

Automatic Sat- ellite Program Recording

This facility allows you to automatically record a satellite program which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the VCR's rear AUDIO/ VIDEO IN or S VIDEO IN* (L-1) connectors and program the timer on the satellite receiver; the VCR starts recording when the signals input from the satellite receiver to the rear AUDIO/VIDEO IN or S VIDEO IN (L-1) connectors, and when there is no input signals the VCR stops recording and the power shuts off.

* If you have connected the satellite receiver to the VCR's

S VIDEO IN connector, set "REAR AUX INPUT" to "S-VIDEO" at the Function screen (☞ pg. 56).

Before performing the following steps:

●Program the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

REC LINK

7 8 9

0 4

−

+

1

2

SET TAPE SPEED

Press SP/EP to set the tape speed.

ENGAGE AUTO SATELLITE PROG REC MODE

Press and hold REC LINK for about 2 seconds. The button lights up and the VCR turns off automatically.

●To disengage the Auto Satellite Prog Rec mode, press REC LINK. The button's light goes off.

●If the VCR's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

1

SP/EP

NOTES:

ATTENTION

●Be sure not to turn on the satellite receiver before the program is executed; otherwise, the VCR will start recording when the satellite receiver's power is turned on.

●If you have connected another appliance other than a satellite receiver to the rear AUDIO/VIDEO IN or S VIDEO IN (L-1) connectors, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the VCR will start recording when the connected appliance's power is turned on.

●Auto Satellite Prog recording and timer-recording cannot be done at the same time.

●Auto Satellite Prog recording is only possible with the rear AUDIO/VIDEO IN or S VIDEO IN (L-1) connectors.

●When the Auto Satellite Prog Rec mode is engaged or the VCR's power is turned off after Auto Satellite Prog recording is finished, the VCR will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.

●The REC LINK button's light blinks while Auto Satellite Prog recording is in progress.

●Pressing the VCR's POWER button while Auto Satellite Prog recording is in progress turns off the VCR's power and disengages the Auto Satellite Prog Rec mode.

●If there is more than one satellite program you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 1 will apply to all the programs for Auto Satellite Prog recording.

●The Active Video Calibration (☞ pg. 38) does not work while Auto Satellite Prog recording is in progress.

●Auto Clock (☞ pg. 12) does not work when the Auto Satellite Prog Rec mode is engaged.

●Depending on the type of satellite receiver, the VCR may not record a short portion at the beginning of the program or may record slightly longer than the actual length of the program.

●If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the VCR will not start Auto Satellite Prog recording even though the REC LINK button's light blinks. When the satellite receiver shuts off once and is turned back on again, the VCR starts recording.

●You can also record a program from your cable system in the same way if the system has a timer and is connected to the VCR's rear AUDIO/VIDEO IN or S VIDEO IN (L-1) connectors.

●When you press the VCR's REC LINK button to engage the Auto Satellite Prog Rec mode, if the REC LINK button does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*.

If this is the case, perform "Express Timer Programming" (☞ pg. 49) to timer-record a satellite program.

*Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.

HR-S7600U-EN45-64

54

99.4.28, 2:05 PM

Page 53 Page 55
Image 54
Page 53 Page 55
Contents HR-S7600U Dear Customer Do not place the VCRInstallation Antenna Installation InstructionsBefore YOU Install Your NEW VCR USEServicing Contents Connections RF Cable supplied Back of VCRVideo Cable Connect VCR to TVEN I Nitial Sett Ings Plug & Play SetupPlug & Play Auto Clock Set/Auto Tuner SetInformation Language Preparation Access Clock SETClock Scan #Select Host Channel Select D.S.T. ModeSET Auto Clock to on Semi-AutoSET Time Select Time ZoneReturn to Normal Screen SET DateTuner Access Main Menu ScreenAccess Tuner SET Screen SETAdd Or Delete a Channel Access ManualChannel Time Scan #Attach Controller Cable Box ControlSituate Controller Connect Cable BOX to VCRSelect Cable BOX Access Cable BOX SETTurn on Cable BOX Output ChannelEnter Cable BOX Brand Access Cable BOX Brand SET ScreenInitial Settings MenuDBS Receiver Control Connect DBS Receiver To VCRDBS receiver Turn on DBS Receiver Access Initial SET ScreenAccess DBS Receiver SET Screen Set DBS Receiver Output Channel & DBS Receiver BrandAccess DBS Receiver SET DBS Receiver BrandSimple Playback Simple Recording Frame Playback Playback FeaturesActivate FRAME-BY Still Picture/Frame-By- Frame PlaybackAdjust Manual Tracking Access Distant CodeEngage Manual Tracking Mode Start SearchLayback and Recording Features Access Function SET ScreenSelect Picture Control SET Mode Picture ControlSelect The Soundtrack Video StabilizerStart Repeat Stop RepeatSuperimpose Access Function SETMode Select Superimpose SETMake Connection Access Main Menu ScreenAV Compu Link Playback ExamplePerform Movie Access Skip MenuSelect Mode AdvanceCommercial Advance Commercial Advance works as followsPress CH 5 or Time Select CA Playback SET ModeReturn to Normal Screen CA RECORD, then pressVariable-Speed Search/ Reverse Motion Playback Audio signal during TimeScanTime Scan Playback tape 1 2 3 4Speed Audio output Skip Over Unwanted SectionsSkip Search Pro-SlowTimescan AUDIO, then ON/OFF as required Default setting is onTimeScan Audio To set to on or OFFSET Mode Digital TBC/NRDigital R3 Active Video Calibration Video CalibrationPlayback RecordingStart Playback Recording Features VHS Super VHS, S-VHS ET and VHS Press S-VHS ET. The button lights up Select S-VHS ET SET ModeSuper VHS ET PanelStereo And SAP Second Audio Program To Record SAP ProgramsTo move the on-screens audio levels by one Number VCR Plus+ Timer ProgrammingTimer Recording Enter Pluscode NumberEngage Timer Mode EN Timer RecordingCheck Program Data Initial SET, then press VCR Plus+ SetupVCR Plus+ Guide Channel Matching OK or Time Scan #Input Receiving Channel Number Access Guide Channel SET ScreenInput Guide Channel Number Press CH5, Time ScanExpress Timer Programming SET Program DateSET Channel Number Unless DBS Receiver SET is Set to OFF pg , If you are using a DBS receiverPress SP/EP to set the tape speed Band indication TV or CatvCheck, Cancel And Revise Cancel or Revise a ProgramRE-ENGAGE Timer ProgramsAuto Timer Select Auto SP=EP Timer SET ModeAuto SP=EP Timer Or Time Scan %ÞSET Recording Duration Instant Timer Recording ITREngage ITR Mode Press REC on the front panelEngage Auto Satellite Prog REC Mode Automatic Sat- ellite Program RecordingBefore performing the following steps Edit To Or From Another Edit From a Camcorder EditingStart Player Enable Remote Pause Function Return to Normal ScreenSet your VCR to its record mode Start RecorderLocate END Point Reset the CounterInsert Editing Locate Start PointEngage Insert Editing Start EditingEND Insert Editing Engage Audio Dubbing SET RECORDER’S Input ModeAudio Dubbing Start DubbingTurn on the TV Speci AL Features ENTV Multi-Brand Remote Control SET TV Brand CodeTurn on the Cable BOX EN Special FeaturesCable Box Multi-Brand Remote Control Operate Cable BOXEnter DBS Receiver Brand DBS Receiver Multi-Brand Remote ControlTurn on the DBS Receiver Operate DBS ReceiverPlug in Power Cord Unplug Vcrs PowerSET Remote Control Turn VCR Power onTroubleshooting EN Cassette gets stuck partwayMake sure the cassettes window is Timer again RoubleshootingOther Problems When scanning channels, someCan the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?What happens if the tape runs out during recording? Index MBR Multi-Brand Remote Code SettingVCR Plus+ Timer Programming List Of TermsFront View Rear View Remote Control EN IndexVideo connectors in x 2, OUT x Speci Fications20C to 60C -4F to140F HOW to Locate Your JVC Service Center Limited Warranty HR-S7600U
Top Page Image Contents