JVC HR-S7600U manual Turn on the DBS Receiver, Enter DBS Receiver Brand, Operate DBS Receiver

Page 63

BR SET

EN63

DBS Receiver Multi-Brand Remote Control

The VCR's remote control can control functions on the brands of DBS (Direct Broadcast Satellite) receivers listed below.

CABLE/DBS

POWER

TURN ON THE DBS RECEIVER

1

 

2

3

 

 

ENTER

 

 

2

4

5

6

NUMBER

 

 

 

7

 

8

9

 

 

 

0

 

4

1

STOP

3

TV CH+/–

1 Turn the power on using the DBS receiver's remote control.

ENTER DBS RECEIVER

BRAND

2 While holding down CABLE/DBS on the VCR’s remote control, press MBR SET and use the NUMBER keys to enter the DBS receiver brand number from the chart in the left column and then press STOP.

Follow the example shown below.

The DBS receiver's power should go off. If it does, try other operations (step 3).

Once you have set the remote control to operate the DBS receiver, you don't have to repeat this step until you replace the remote control's batteries.

OPERATE DBS RECEIVER

3 First, while holding down CABLE/DBS, press the corresponding button: POWER, TV CH +/–, NUMBER keys.

Depending on the DBS receiver you may have to press ENTER after having pressed the NUMBER keys.

To change the DBS receiver's channel, press TV CH +/– or the NUMBER keys. (The CH +/– button can be used to change the VCR's channel only.)

NOTES:

Depending on the type of DBS receiver, there may be cases where some or all functions cannot be operated using the remote control.

It's not possible to operate a DBS receiver that is not equipped with a remote control sensor.

Though ECHOSTAR has a number of different remote codes, this remote control is applicable only to one of those codes preset at the factory.

It's not possible to set the remote control for both your DBS receiver and a cable box at the same time. You can only set the remote control to operate one of these units at a time.

DBS BRAND NAME

BRAND CODE

 

 

JVC (DISH Network)

51

ECHOSTAR (DISH Network)

51

PRIMESTAR

50

SONY (DSS)

41

RCA (DSS)

40

 

 

(Ex.) To set remote control to JVC 51:

CABLE/

MBR SET

 

 

DBS

A/B

 

 

 

5

1

STOP

 

 

Hold

Press in succession

down

 

Release

HR-S7600U-EN45-64

63

99.4.28, 2:05 PM

Image 63
Contents HR-S7600U Do not place the VCR Dear CustomerAntenna Installation Instructions InstallationBefore YOU Install Your NEW VCR USEServicing Contents Connections Connect VCR to TV Back of VCRVideo Cable RF Cable suppliedAuto Clock Set/Auto Tuner Set Plug & Play SetupPlug & Play EN I Nitial Sett IngsInformation Language Scan # Access Clock SETClock PreparationSemi-Auto Select D.S.T. ModeSET Auto Clock to on Select Host ChannelSET Date Select Time ZoneReturn to Normal Screen SET TimeSET Access Main Menu ScreenAccess Tuner SET Screen TunerTime Scan # Access ManualChannel Add Or Delete a ChannelConnect Cable BOX to VCR Cable Box ControlSituate Controller Attach ControllerOutput Channel Access Cable BOX SETTurn on Cable BOX Select Cable BOXMenu Access Cable BOX Brand SET ScreenInitial Settings Enter Cable BOX BrandDBS Receiver Control Connect DBS Receiver To VCRDBS receiver Set DBS Receiver Output Channel & DBS Receiver Brand Access Initial SET ScreenAccess DBS Receiver SET Screen Turn on DBS ReceiverSET DBS Receiver Brand Access DBS ReceiverSimple Playback Simple Recording Still Picture/Frame-By- Frame Playback Playback FeaturesActivate FRAME-BY Frame PlaybackStart Search Access Distant CodeEngage Manual Tracking Mode Adjust Manual TrackingPicture Control Access Function SET ScreenSelect Picture Control SET Mode Layback and Recording FeaturesVideo Stabilizer Select The SoundtrackStop Repeat Start RepeatSelect Superimpose SET Access Function SETMode SuperimposeExample Access Main Menu ScreenAV Compu Link Playback Make ConnectionAdvance Access Skip MenuSelect Mode Perform MovieCommercial Advance works as follows Commercial AdvanceCA RECORD, then press Select CA Playback SET ModeReturn to Normal Screen Press CH 5 or TimePlayback tape 1 2 3 4 Audio signal during TimeScanTime Scan Variable-Speed Search/ Reverse Motion PlaybackPro-Slow Skip Over Unwanted SectionsSkip Search Speed Audio outputTo set to on or OFF ON/OFF as required Default setting is onTimeScan Audio Timescan AUDIO, thenSET Mode Digital TBC/NRDigital R3 Video Calibration Active Video CalibrationPlayback RecordingStart Playback Recording Features VHS Super VHS, S-VHS ET and VHS Panel Select S-VHS ET SET ModeSuper VHS ET Press S-VHS ET. The button lights upTo Record SAP Programs Stereo And SAP Second Audio ProgramTo move the on-screens audio levels by one Enter Pluscode Number VCR Plus+ Timer ProgrammingTimer Recording NumberEngage Timer Mode EN Timer RecordingCheck Program Data OK or Time Scan # VCR Plus+ SetupVCR Plus+ Guide Channel Matching Initial SET, then pressPress CH5, Time Scan Access Guide Channel SET ScreenInput Guide Channel Number Input Receiving Channel NumberExpress Timer Programming SET Program DateSET Channel Number Band indication TV or Catv If you are using a DBS receiverPress SP/EP to set the tape speed Unless DBS Receiver SET is Set to OFF pg ,Programs Cancel or Revise a ProgramRE-ENGAGE Timer Check, Cancel And ReviseOr Time Scan %Þ Select Auto SP=EP Timer SET ModeAuto SP=EP Timer Auto TimerPress REC on the front panel Instant Timer Recording ITREngage ITR Mode SET Recording DurationEngage Auto Satellite Prog REC Mode Automatic Sat- ellite Program RecordingBefore performing the following steps Edit To Or From Another Editing Edit From a CamcorderStart Recorder Enable Remote Pause Function Return to Normal ScreenSet your VCR to its record mode Start PlayerLocate Start Point Reset the CounterInsert Editing Locate END PointEngage Insert Editing Start EditingEND Insert Editing Start Dubbing SET RECORDER’S Input ModeAudio Dubbing Engage Audio DubbingSET TV Brand Code Speci AL Features ENTV Multi-Brand Remote Control Turn on the TVOperate Cable BOX EN Special FeaturesCable Box Multi-Brand Remote Control Turn on the Cable BOXOperate DBS Receiver DBS Receiver Multi-Brand Remote ControlTurn on the DBS Receiver Enter DBS Receiver BrandTurn VCR Power on Unplug Vcrs PowerSET Remote Control Plug in Power CordTroubleshooting EN Cassette gets stuck partwayMake sure the cassettes window is Roubleshooting Timer againWhen scanning channels, some Other ProblemsCan the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?What happens if the tape runs out during recording? List Of Terms MBR Multi-Brand Remote Code SettingVCR Plus+ Timer Programming IndexFront View Rear View EN Index Remote ControlVideo connectors in x 2, OUT x Speci Fications20C to 60C -4F to140F HOW to Locate Your JVC Service Center Limited Warranty HR-S7600U