JVC HR-S7600U manual Roubleshooting, Timer again

66EN

TROUBLESHOOTING (cont.)

TIMER RECORDING
SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1. Timer recording won’t work.	● The clock and/or the timer have	Set the clock and/or timer correctly.
	been set incorrectly.
	● The timer is not engaged.	Press TIMER and check to make sure
		that ä appears on the front display
		panel.
	● The VCR has not been set up properly.	Re-perform the set-up procedures.
		Make sure you have compensated for
		Guide Channel and VCR or cable box
		channel number mismatches
		(☞ pg. 47).
2. Timer programming won’t work.	● Timer recording is in progress.	Timer programming can’t be performed
		when timer recording is in progress.
		Wait until it finishes.
3. ä and ]on the front display	● The timer is engaged but there’s no	Load a cassette with the record safety
panel won’t stop blinking.	cassette loaded.	tab intact, or with the hole covered
		with adhesive tape.
4. The cassette is automatically	● The loaded cassette has had its	Remove the cassette and cover its
ejected, and ä and ] on the	record safety tab removed.	hole with adhesive tape, or replace it
front display panel won’t stop		with a cassette on which the safety
blinking.		tab is intact.
5. ä blinks for 10 seconds and the	● TIMER has been pressed when there	Check the programmed data and re-
timer mode is disengaged.	are no programs in memory, or the	program as necessary, then press
	timer record program information	TIMER again.
	has not been programmed correctly.
6. The cassette is automatically	● The end of tape was reached during	The program may not have been
ejected, the power shuts off and ä	timer recording.	recorded in its entirety. Next time
and ] won’t stop blinking.		make sure you have enough time on
		the tape to record the entire program.
7. Cable channels are not automatically	● The Controller is not properly	Connect the Controller correctly
switched during timer recording.	connected to the VCR.	(☞ pg. 16).
	● The output channel selected in the	After confirming your cable box’s
	Cable Box Set screen is incorrect.	output channel number, re-access the
		Cable Box Set screen and select the
		correct number (☞ pg. 17).
	● The cable box’s power is off.	Make sure the power is on before
		timer recording starts.
8. Satellite channels are not automati-	● The Controller is not properly	Connect the Controller correctly
cally switched during timer	connected to the VCR.	(☞ pg. 19).
recording.	● The output channel selected in the	After confirming your DBS receiver’s
	DBS Receiver Set screen is incorrect.	output channel number, re-access the
		DBS Receiver Set screen and select
		the correct number (☞ pg. 20).
	● The VCR is not set correctly to	Set the correct DBS Receiver brand
	control the DBS Receiver	code (☞ pg. 21).
	● The DBS receiver’s power is off.	Make sure the power is on before
		timer recording starts.
9. Timer recording begins as sched-	● Even though you don't use an	Set "CABLE BOX SET" to "OFF"
uled, but the channel is always	external Cable Box, "CABLE BOX	(☞ pg. 17).
incorrect.	SET" is set to "ON".
10.We moved, and now VCR Plus+	● The receivable stations in the new area	Re-perform the VCR Plus+ setup
doesn’t work properly.	are received on different channels than	procedure (☞ pg. 47).
	those in the previous area.
11.“PROGRAM FULL” is displayed on	● All 8 programs of the VCR’s timer	Wait until a space in memory clears,
the screen.	memory are used.	or cancel unnecessary program
		information (☞ pg. 51).

HR-S7600U-EN65-76 66 99.4.28, 2:06 PM