TimeScan Audio, Speed SP Speed LP Audio output

EN19

TimeScan

Names of special-effects playback

Speed SP

Speed LP

Audio output

Reverse

Forward

Play

Slow-Motion

*Still

Slow-Motion

Play

(Time Jog**)

-9x

-7x

-5x

-3x

-1x

-1/2x

1/2x

1.5x

-7x

-3x

-1/2x

1/2x

1.5x

Audio is output.

Audio is not

Audio is

Audio is output.

output.

**Still mode cannot be engaged using the remote control's % or %button. Still mode can be engaged by pressing the PAUSE button.

** Smooth slow motion delivering an uninterrupted moving image without distortion.

●The speed is shown during TimeScan in the upper right corner of the TV screen for approx. 5 seconds. (The display may be distorted.)

●To resume normal playback, press PLAY.

●Picture and audio may become distorted when the recording speed changes. When this happens, resume normal playback once, and then try using TimeScan again.

●The picture may be noisy or there may be a loss of colour when you change the playback speed. (More noise will appear with LP recordings.)

●Noise may appear or the upper part of the picture may be distorted during still, frame-by-frame playback, 2x search of LP recordings, or depending on the tape being used.

●Picture may appear distorted in comparison to normal playback.

●When normal playback resumes from search (including TimeScan), still, slow motion or frame-by-frame playback, the picture may jitter vertically momentarily depending on the type of TV being used.

●In TimeScan mode there will be a time lag between the video and the audio and noise may appear in the audio signal.

●TimeScan sound quality will differ in comparison to normal playback.

●When material such as music videos where there is non-stop sound (very few breaks in the soundtrack) are viewed at 1.5x or 2x normal speed, the audio playback may be faster than normal.

●Depending on the type of tape contents, the sound may not be clear during forward slow-motion playback.

●Time Jog cannot be activated by pressing PAUSE for longer than 2 seconds.

●When the playback direction is reversed, it takes approximately 6 seconds until sound is heard.

●Picture will be monochrome with an LP-recorded MESECAM tape during TimeScan.

●When playing back an NTSC tape, the speeds differ from those listed above and are not shown on the TV screen.

●TimeScan at -1/2x, 1/2x and 1.5x normal speed are not possible with a MESECAM tape.

●The operations by the remote's JOG dial/SHUTTLE ring do not include TimeScan; noise will appear on the screen and audio will not be output.

If you don't want to hear TimeScan audio, set "TIME SCAN AUDIO" to "OFF" (See below).

TimeScan Audio

HR-S9500EHR-S9500EH

MODE SET

The audio output can be set ON/OFF during TimeScan. Select ON/OFF as required.

* The default setting is "ON".

1Press MENU to access the Main Menu screen.

2Move the highlight bar (pointer) to "MODE SET" by

pressing %Þ, then press OK or %.

3Move the highlight bar (pointer) to "TIME SCAN AUDIO"

by pressing %Þ, then press OK or %to select "ON" or "OFF".

4 Press MENU to return to the normal screen.

AUTO TIMER	OFF	AUTO TIMER	OFF
O. S. D.	ON	O. S. D.	ON
B. E. S. T.	ON	B. E. S. T.	ON
AUTO SP=LP TIMER	OFF	AUTO SP=LP TIMER	OFF
DIGITAL 3R	ON	DIGITAL 3R	ON
POWER SAVE	OFF	S-VHS	AUTO
S-VHS	AUTO	EDIT	OFF
NEXT PAGE		NEXT PAGE
[5°] =		[5°] =
[MENU] : EXIT		[MENU] : EXIT
PREVIOUS PAGE	OFF	PREVIOUS PAGE	VIDEO
EDIT	OFF	AV2 SELECT	VIDEO
AV2 SELECT	VIDEO	COLOUR SYSTEM PAL/NTSC
COLOUR SYSTEM PAL/NTSC		TIME SCAN AUDIO	ON
TIME SCAN AUDIO	ON

[5°] =	[5°] =
[MENU] : EXIT	[MENU] : EXIT