JVC HR-S9500EH specifications Start Editing, END Insert Editing

Page 41

PLAY

 

A

INSERT

.

DUB

 

1 2 3

2

4 5 6

7 8 9

0000

0

4

 

 

1

PLAY

3

 

 

 

 

 

 

 

E

 

N

 

41

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

ENGAGE INSERT EDITING

 

 

 

 

Press INSERT.

 

 

 

 

 

 

 

 

Your recorder enters the Insert-Pause mode. (" ", " "

 

 

 

and " " light up on the front display panel.)

 

 

 

 

The TV screen changes from the still picture to the

 

 

 

 

input source you are going to record.

 

 

 

 

 

 

 

 

 

START EDITING

 

 

 

 

 

Load the source cassette and play back the segment that

 

 

 

 

is to be inserted. When you reach the start of the

 

 

 

7 section of the source tape that you wish to insert, press

 

 

 

 

PLAY to start the tape in your recorder; Insert Editing

 

 

 

 

begins at this point.

"" and "" are displayed on the front display panel.

END INSERT EDITING

8 At counter "0:00:00", Insert Editing will stop automati- cally while the tape continues running in the Play mode. If you wish to stop Insert Editing before the specified edit-out point, press 0000.

FOR AV INSERT EDITING

If you want to replace the picture, Hi-Fi audio soundtrack and

normal audio soundtrack all at the same time...

... In step 6 above, after you press INSERT, press A. DUB also. ("" and "" blink and "" lights up on the front display panel.)

NOTES:

Suitable leads can be obtained from your dealer.

Insert editing is not possible with cassettes whose safety tab has been removed.

When insert editing is performed on a tape that has been recorded on another video recorder, the inserted portion may appear distorted.

In insert editing, the recording speed (SP/LP) is determined by the previous recording to be replaced. If the previous recording's speed changes within a single edit, the inserted picture will be distorted at the switching point.

A small portion of the recording which precedes an insert edit may become erased.

Insert Editing is also possible using the rear panel AV1 IN/ OUT or AV2 IN/DECODER connector. When using these connectors, make sure to select the correct input mode in step 2.

Image 41
Contents HR-S9500E/EH Safety Precautions Do not place the recorder For ItalyBasic Connections Check ContentsSituate Recorder Connect Recorder to MainsBack of Recorder Video ConnectionConnect Recorder to TV If you are referring to the front display panel Auto Set UpIf you are referring to the on-screen display International Telephone Country CodeLanguage Code Supplied with your TV set for how to do thisVia the provided RF cable only RF connection Your Video ChannelLanguage for the on-screen display If both auto channel set and auto clock set have failedJust Clock Just Clock onLanguage On-Screen Displays Power Save Mode OK or% Colour System SetAbout Ntsc Playback Load a Cassette Basic PlaybackPoint Start PlaybackActivate HIGH-SPEED Search Playback FeaturesPlayback Override Automatic Tracking Adjust TrackingManually Return to AutomaticDigital 3R Digital TBC/NRSpatializer Activate SpatializerSoundtrack Selection During PlaybackTimeScan Audio signal during TimeScanTimeScan Audio TimeScanSpeed SP Speed LP Audio output HR-S9500EHR-S9500EHBasic Recording Recording Features Locate Start Point Engage RECORD-PAUSE ModeResume Recording VHS Super VHS and VHSHi-Fi Audio Recording Level Control Adjust AudioReceiving Stereo And Bilingual Programmes To Record Stereo And Bilingual Programmes A2Highlight bar pointer to MODE%SET, then press S.T. Picture SystemPreparation Playback RecordingOr press Record on the recorder During B.E.S.TTimer Programming Press SP/LP Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET VPS/PDC ModeEngage RECORDER’S VPS/PDC RecordingSTOP+/-,DATE+/-,TV PROG+/-,VPS/PDC, SP/LP Check, Cancel And Replace ProgrammesAuto Timer Auto SP→LP TimerBefore performing the following steps Prog REC ModeAutomatic Satellite Programme Recording Remove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVSET Satellite Tuner Brand Code Satellite Tuner Multi-Brand Remote ControlOperate Satellite Tuner Number keysPreparation For Editing Editing Mode SettingReturn to Normal Screen Advantages Of S-VHS Video RecordersEdit From Camcorder If the camcorder has an S-VIDEO output connector RecorderRecorder PlayerEdit To Or From Another Video Recorder Recorder Player AV2 Select SettingReset the Counter SET Input ModeInsert Editing Locate END PointEND Insert Editing Start EditingRandom Assemble Editing Locate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditEngage Audio Dubbing Audio DubbingStart Dubbing END Audio DubbingAccess Jlip ID NO. SET Access Initial SETInterface Protocol Connector SET Jlip ID NumberConnection To a Satellite Tuner SwitchSatellite Tuner Unit AV2 IN/DECODERSelect Input Mode Connecting Using a DecoderConnect Decoder SET TunerRear View Connecting Using a Stereo SystemAUX in or Tape Monitor Exit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelAuto Channel Set Tuner SetPress OK or% Countrys name, then press OK or%View Confirmation Screen Perform Auto Channel SETStoring Channels Manually Enter NEW Channel InformationChange Station Channel Position When Receiving a Scrambled BroadcastDelete a Channel Switch Stations Access ManualChannel SET Screen Select NEW StationStation Name TV Station And ID ListFine-Tuning Channels Already Stored Perform TuningSelect Channel to FINE-TUNE Press OK twice. The Manual Channel Set screen appearsNumber Showview SetupEnter Receiving Channel Position Number Guide Program Number SetAccess Clock SET Screen Access Initial SET ScreenClock Set SET Date and TimeStart Clock Operation SET Just ClockSET Clock Data Source Channel Position To the AV mode TroubleshootingTimer Recording Ä remain lit on the display panel. Is there Problem? EN Questions and AnswersIndex EN Index Remote Control Frequency synthesized tuner Maximum recording timeMemo Ex. Francais is selected for Belgium HR-S9500E/EHInternational Telephone Language Code For More Information see INSTRUCTIONS/P6