|
|
|
|
|
|
|
|
|
|
| E |
| N |
| 61 | |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| TIMER RECORDING |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
| SYMPTOM |
| POSSIBLE CAUSE |
| CORRECTIVE ACTION |
| |||||||
| 1. | Timer recording won’t work. | ● The clock and/or the timer have |
| ||||||||||||
|
|
|
|
|
| been set incorrectly. | settings. |
| ||||||||
|
|
|
|
|
| ● The timer is not engaged. | Press äand confirm that “ä“ is |
| ||||||||
|
|
|
|
|
|
|
|
| displayed on the display panel. |
| ||||||
|
|
|
|
|
| |||||||||||
| 2. | Timer programming is not possible. | ● Timer recording is in progress. | Timer programming can’t be |
| |||||||||||
|
|
|
|
|
|
|
|
| performed while a timer recording is |
| ||||||
|
|
|
|
|
|
|
|
| in progress. Wait until it finishes. |
| ||||||
|
|
|
|
|
| |||||||||||
| 3. | “ä“ and “]“ on the display | ● The timer is engaged but there’s no | Load a cassette with the Record |
| |||||||||||
|
| panel won’t stop blinking. | cassette loaded. | Safety tab intact, or cover the hole |
| |||||||||||
|
|
|
|
|
|
|
|
| using adhesive tape. |
| ||||||
|
|
|
|
|
| |||||||||||
| 4. | The cassette is automatically | ● The loaded cassette has had its | Remove the cassette and cover the |
| |||||||||||
|
| ejected, and “ä“ and “]“ on the | Record Safety tab removed. | hole with adhesive tape, or insert a |
| |||||||||||
|
| display panel won’t stop blinking. |
|
|
| cassette with the Record Safety tab |
| |||||||||
|
|
|
|
|
|
|
|
| intact. |
| ||||||
|
|
|
|
|
| |||||||||||
| 5. | “ä“ blinks for 10 seconds and the | ● ä has been pressed when there are | Check the programmed data and re- |
| |||||||||||
|
| Timer mode is disengaged. | no programs in memory, or the timer | program as necessary, then press ä |
| |||||||||||
|
|
|
|
|
| record information has been | again. |
| ||||||||
|
|
|
|
|
| programmed incorrectly. |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| |||||||||||
| 6. | The cassette is automatically | ● The end of the tape was reached | The programme may not have been |
| |||||||||||
|
| ejected, the power shuts off and | during timer recording. | recorded in its entirety. Next time |
| |||||||||||
|
| “ä“ and “]“ won’t stop |
|
|
| make sure you have enough time on |
| |||||||||
|
| blinking. |
|
|
| the tape to record the entire |
| |||||||||
|
|
|
|
|
|
|
|
| programme. |
| ||||||
|
|
|
|
|
| |||||||||||
| 7. | SHOWVIEW does not | ● The recorder’s channel positions | Refer to "Guide Program Number Set" |
| |||||||||||
|
| properly. | have been set incorrectly. | and |
| |||||||||||
|
|
|
|
|
|
|
|
| (☞ pg. 57). |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| OTHER PROBLEMS |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
| SYMPTOM |
| POSSIBLE CAUSE |
| CORRECTIVE ACTION |
| |||||||
| 1. | Whistling or howling is heard from | ● The camcorder’s microphone is too | Position the camcorder so its |
| |||||||||||
|
| the TV during camcorder record- | close to the TV. | microphone is away from the TV. |
| |||||||||||
|
| ing. | ● The TV’s volume is too high. | Turn the TV’s volume down. |
| |||||||||||
|
|
|
|
|
| |||||||||||
| 2. | When scanning channels, some of | ● Those channels have been desig- | If you need the skipped channels, |
| |||||||||||
|
| them are skipped over. | nated to be skipped. | restore them (☞ pg. 52). |
| |||||||||||
|
|
|
|
|
| |||||||||||
| 3. | The channel cannot be changed. | ● Recording is in progress. | Press PAUSE to pause the recording, |
| |||||||||||
|
|
|
|
|
|
|
|
| change channels, then press PLAY to |
| ||||||
|
|
|
|
|
|
|
|
| resume recording. |
| ||||||
|
|
|
|
|
| |||||||||||
| 4. | Channel settings that were made | ● After the manual settings were | Perform manual setting again. |
| |||||||||||
|
| manually seem to have changed or | made, Auto Channel Set was |
|
|
|
|
|
|
|
| |||||
|
| disappeared. | performed. |
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
| |||||||||||
| 5. | No channels are stored in the | ● The TV aerial cable was not | Connect the TV aerial cable to the |
| |||||||||||
|
| recorder's memory. | connected to the recorder when | recorder properly and turn off the |
| |||||||||||
|
|
|
|
|
| Auto Set Up was performed. | recorder power once, then turn the |
| ||||||||
|
|
|
|
|
|
|
|
| recorder power back on again. The |
| ||||||
|
|
|
|
|
|
|
|
| recorder will try Auto Set Up again |
| ||||||
|
|
|
|
|
|
|
|
| (☞ pg. 6). |
| ||||||
|
|
|
|
|
| |||||||||||
| 6. | The remote control won’t operate | ● The remote control brand setting is |
| ||||||||||||
|
| the TV or satellite tuner. | incorrect. | correct brand (☞ pg. 34, 35). |
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|