JVC HR-S9500EH specifications Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 49

SUBSIDIARYSETTINGSEN49

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 6).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection), or via the provided RF cable, the provided S-Video cable and an audio cable (S-VIDEO connection), since you do not need the video channel you have to set the video channel to off.

If you have connected the video recorder to your TV via the provided RF cable only (RF connection), you have to set the correct video channel.

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

1

2

ACCESS VIDEO CHANNEL SET MODE

Hold down STOP (5/8) on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

With AV Connection or S-VIDEO Connection

Press TV PROG – until the display panel shows "–OUT– –".

●Now the video channel is set to off.

With RF Connection

Press TV PROG + or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area.

(Ex.) If channel 50 is available in your area

Then set your TV to UHF channel 50.

●If the two vertical white bars appear clearly on the screen as shown to the right, go to step 3.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET MODE

3 Press OK on the remote control.

With AV Connection or S-VIDEO Connection:

To view picture signals from the video recorder, set your TV to its AV mode.

With RF Connection:

The channel on which the screen in step 2 appears clearly is your video channel.

To view picture signals from the video recorder, set your TV to the Video Channel.

Page 48 Page 50
Image 49
Page 48 Page 50
Contents HR-S9500E/EH Safety Precautions Do not place the recorder For ItalyBasic Connections Check ContentsSituate Recorder Connect Recorder to MainsConnect Recorder to TV Video ConnectionBack of Recorder If you are referring to the front display panel Auto Set UpIf you are referring to the on-screen display International Telephone Country CodeLanguage Code Supplied with your TV set for how to do thisVia the provided RF cable only RF connection Your Video ChannelLanguage for the on-screen display If both auto channel set and auto clock set have failedJust Clock Just Clock onLanguage On-Screen Displays Power Save Mode About Ntsc Playback Colour System SetOK or% Load a Cassette Basic PlaybackPoint Start PlaybackPlayback Playback FeaturesActivate HIGH-SPEED Search Override Automatic Tracking Adjust TrackingManually Return to AutomaticDigital 3R Digital TBC/NRSpatializer Activate SpatializerSoundtrack Selection During PlaybackTimeScan Audio signal during TimeScanTimeScan Audio TimeScanSpeed SP Speed LP Audio output HR-S9500EHR-S9500EHBasic Recording Recording Features Locate Start Point Engage RECORD-PAUSE ModeResume Recording VHS Super VHS and VHSHi-Fi Audio Recording Level Control Adjust AudioReceiving Stereo And Bilingual Programmes To Record Stereo And Bilingual Programmes A2Preparation S.T. Picture SystemHighlight bar pointer to MODE%SET, then press Playback RecordingOr press Record on the recorder During B.E.S.TTimer Programming Press SP/LP Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET VPS/PDC ModeEngage RECORDER’S VPS/PDC RecordingSTOP+/-,DATE+/-,TV PROG+/-,VPS/PDC, SP/LP Check, Cancel And Replace ProgrammesAuto Timer Auto SP→LP TimerAutomatic Satellite Programme Recording Prog REC ModeBefore performing the following steps Remove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVSET Satellite Tuner Brand Code Satellite Tuner Multi-Brand Remote ControlOperate Satellite Tuner Number keysPreparation For Editing Editing Mode SettingReturn to Normal Screen Advantages Of S-VHS Video RecordersEdit From Camcorder If the camcorder has an S-VIDEO output connector RecorderRecorder PlayerEdit To Or From Another Video Recorder Recorder Player AV2 Select SettingReset the Counter SET Input ModeInsert Editing Locate END PointEND Insert Editing Start EditingRandom Assemble Editing Locate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditEngage Audio Dubbing Audio DubbingStart Dubbing END Audio DubbingAccess Jlip ID NO. SET Access Initial SETInterface Protocol Connector SET Jlip ID Number Connection To a Satellite Tuner Switch Satellite Tuner Unit AV2 IN/DECODERSelect Input Mode Connecting Using a DecoderConnect Decoder SET TunerAUX in or Tape Monitor Connecting Using a Stereo SystemRear View Exit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelAuto Channel Set Tuner SetPress OK or% Countrys name, then press OK or%View Confirmation Screen Perform Auto Channel SETStoring Channels Manually Enter NEW Channel InformationDelete a Channel When Receiving a Scrambled BroadcastChange Station Channel Position Switch Stations Access ManualChannel SET Screen Select NEW StationStation Name TV Station And ID ListFine-Tuning Channels Already Stored Perform TuningSelect Channel to FINE-TUNE Press OK twice. The Manual Channel Set screen appearsNumber Showview SetupEnter Receiving Channel Position Number Guide Program Number SetAccess Clock SET Screen Access Initial SET ScreenClock Set SET Date and TimeSET Clock Data Source Channel Position SET Just ClockStart Clock Operation To the AV mode TroubleshootingTimer Recording Ä remain lit on the display panel. Is there Problem? EN Questions and AnswersIndex EN Index Remote Control Frequency synthesized tuner Maximum recording timeMemo Ex. Francais is selected for Belgium HR-S9500E/EHInternational Telephone Language Code For More Information see INSTRUCTIONS/P6
Top Page Image Contents