JVC HR-S9500E Connection To a Satellite Tuner, Satellite Tuner Unit, AV2 IN/DECODER, Switch

Page 46

46ENSYSTEMCONNECTIONS

Connection To A Satellite Tuner

The AV2 IN/DECODER connector on the rear panel of your recorder allows simple connection to a satellite tuner.

Aerial connector

Outdoor Unit	Aerial	Back of TV
		Back of TV
		21-pin AV input
Satellite Cable	TV Aerial	connector (SCART)
Satellite Cable	TV Aerial
	cable

Satellite Tuner Unit

ANT. IN

EXT.2EXT.1

DECODER

VCR

TV

RF OUT

Mains outlet

AV1 OUT

S OUT

COMP. Y/C

		ANT. IN
AV1 IN/OUT	R	L
	AUDIO OUT
		JLIP
		RF OUT
AV2 IN/DECODER
		PAUSE/
		R.A. EDIT

Back of Recorder

AV1 OUT switch

IMPORTANT

Set "AV2 SELECT" to "SAT" on the Mode Set screen (☞ pg. 39). If you set "AV2 SELECT" to "SAT"...

● It is possible to view a satellite programme with the TV set to its AV mode even if the recorder's power is turned off.

● The AV2 IN/DECODER connector's input is the same signal that is controlled by the rear panel AV1 OUT switch as shown below: a- If both the satellite tuner and the TV are compatible with the Y/C signal, set the AV1 OUT switch to Y/C in order to take

advantage of high-quality S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

b- If the satellite tuner and/or the TV are/is not compatible with the Y/C signal, set the AV1 OUT switch to COMP.

	AV2 SELECT setting on	Rear panel AV1 OUT	AV2 IN/DECODER	* The composite signal is a regular video
	the MODE SET screen	switch	connector input signal	signal.
				** The Y/C signal is a signal in which the
		COMP.	Composite signal*	** The Y/C signal is a signal in which the
	SAT	COMP.	Composite signal*	luminance and chrominance signals are
	SAT	Y/C	Y/C signal**	separated.
				separated.

NOTE:

Refer to the instructions supplied with your satellite tuner.

Image 46

Contents HR-S9500E/EH Safety Precautions For Italy Do not place the recorderSituate Recorder Check ContentsBasic Connections Connect Recorder to MainsConnect Recorder to TV Video ConnectionBack of Recorder If you are referring to the on-screen display Auto Set UpIf you are referring to the front display panel International Telephone Country CodeVia the provided RF cable only RF connection Supplied with your TV set for how to do thisLanguage Code Your Video ChannelJust Clock If both auto channel set and auto clock set have failedLanguage for the on-screen display Just Clock onLanguage On-Screen Displays Power Save Mode About Ntsc Playback Colour System SetOK or% Point Basic PlaybackLoad a Cassette Start PlaybackPlayback Playback FeaturesActivate HIGH-SPEED Search Manually Adjust TrackingOverride Automatic Tracking Return to AutomaticDigital TBC/NR Digital 3RSoundtrack Selection Activate SpatializerSpatializer During PlaybackAudio signal during TimeScan TimeScanSpeed SP Speed LP Audio output TimeScanTimeScan Audio HR-S9500EHR-S9500EHBasic Recording Recording Features Resume Recording Engage RECORD-PAUSE ModeLocate Start Point VHS Super VHS and VHSReceiving Stereo And Bilingual Programmes Adjust AudioHi-Fi Audio Recording Level Control To Record Stereo And Bilingual Programmes A2Preparation S.T. Picture SystemHighlight bar pointer to MODE%SET, then press Or press Record on the recorder RecordingPlayback During B.E.S.TTimer Programming Timer Warning Press SP/LPEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeEngage RECORDER’S SET VPS/PDC ModeTimer Mode VPS/PDC RecordingCheck, Cancel And Replace Programmes STOP+/-,DATE+/-,TV PROG+/-,VPS/PDC, SP/LPAuto SP→LP Timer Auto TimerAutomatic Satellite Programme Recording Prog REC ModeBefore performing the following steps SET Remote Control Code Remote Control FunctionsRemove Power Supply RE-SUPPLY PowerSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Operate TVOperate Satellite Tuner Satellite Tuner Multi-Brand Remote ControlSET Satellite Tuner Brand Code Number keysReturn to Normal Screen Editing Mode SettingPreparation For Editing Advantages Of S-VHS Video RecordersRecorder If the camcorder has an S-VIDEO output connector RecorderEdit From Camcorder PlayerEdit To Or From Another Video Recorder AV2 Select Setting Recorder PlayerInsert Editing SET Input ModeReset the Counter Locate END PointStart Editing END Insert EditingRandom Assemble Editing Start R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditStart Dubbing Audio DubbingEngage Audio Dubbing END Audio DubbingInterface Protocol Connector Access Initial SETAccess Jlip ID NO. SET SET Jlip ID NumberSatellite Tuner Unit SwitchConnection To a Satellite Tuner AV2 IN/DECODERConnect Decoder Connecting Using a DecoderSelect Input Mode SET TunerAUX in or Tape Monitor Connecting Using a Stereo SystemRear View Video Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelPress OK or% Tuner SetAuto Channel Set Countrys name, then press OK or%Perform Auto Channel SET View Confirmation ScreenEnter NEW Channel Information Storing Channels ManuallyDelete a Channel When Receiving a Scrambled BroadcastChange Station Channel Position Channel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List Station NameSelect Channel to FINE-TUNE Perform TuningFine-Tuning Channels Already Stored Press OK twice. The Manual Channel Set screen appearsEnter Receiving Channel Position Number Showview SetupNumber Guide Program Number SetClock Set Access Initial SET ScreenAccess Clock SET Screen SET Date and TimeSET Clock Data Source Channel Position SET Just ClockStart Clock Operation Troubleshooting To the AV modeTimer Recording EN Questions and Answers Ä remain lit on the display panel. Is there Problem?Index EN Index Remote Control Maximum recording time Frequency synthesized tunerMemo International Telephone Language Code HR-S9500E/EHEx. Francais is selected for Belgium For More Information see INSTRUCTIONS/P6