JVC SR-9240EK appendix Monitor ON-SCREEN Display, Main Menu Display, Operation

Page 16

4 MONITOR ON-SCREEN DISPLAY

4-2 Main Menu Display

You can display date and time data recorded when an alarm input or power failure occurs, as well as the hour meter (drum rotating time) by selecting the desired item in the main menu.

The timer recording program setting screen, function menu switch setting screen, and date/time setting screen can also be displayed by selecting the desired item in the main menu.

[SHIFT +/–] buttons

[MENU] button
		SR-9240E
VIDEO CASSETTE RECORDER		OPERATE
VIDEO CASSETTE RECORDER
		OPE. LOCK
COUNT/	SHIFT/TRACKING	RESET
CLOCK	MENU	/CANCEL
TIME	TIMER SET/V.LOCK	AL/PL
MODE	REC	RESET
		PAL

[SET +/–] buttons

Main menu screen

MAIN MENU

PROGRAM TIMER

FUNCTION

ALARM IN

POWER LOSS

HOUR METER

CLOCK ADJUST

PRESS (SHIFT, SET)

PRESS (MENU) TO END

Operation

5Connect the VCR's video output connector to the

1monitor's video input connector.

2Turn on the VCR and the monitor.

Press the [MENU] button.

3[The main menu screen is displayed.

Press the [SHIFT +/-] button to move the cursor arrow to the item you want to display.

•Press the [SHIFT +] button to move the cursor arrow

4down. Press the [SHIFT -] button to move it up.

Press the [SET +] or [SET -] button to display the

5selected item.

To end menu operation and restore the normal screen, press the [MENU] button.

●PROGRAM TIMER:

Displays the program setting screen for timer recording.

*Timer programming is not possible if the date and time are not set. In this case, the date/time setting screen will be displayed.

●FUNCTION:

Displays the function menu setting screen.

●ALARM IN:

Displays the date and time when an alarm signal was input.

●POWER LOSS

Displays the date and time when a power failure occurred.

●HOUR METER:

Displays the hour meter (drum rotating time).

●CLOCK ADJUST:

Displays the date/time setting screen.

*Set the date and time before using this unit.

•When the [MENU] button is pressed during playback,

the monitor screen display switches from the playback picture to the input video signal (EE picture) and the

main menu is shown on the screen.

This means that even during playback you can check menu contents. Press the [MENU] button again to

restore the playback picture.

17

Image 16

Contents SR-9240EK Safety Precautions For Your Safety AustraliaConnection to the mains supply DanishOperation Lock Lock indicator Time Mode buttonButton Contents Periodical Maintenance Major FeaturesIntroduction Introduction PrecautionsDaily Inspection Controls and Connectors Front PanelControls and Connectors Display Rear Panel Series recording signal input VCR activation signal inputClock reset signal input Connecting the wires to the terminals 9 toConnecting to a Camera ConnectionsConnections Connecting a System Using a Sequential SwitcherVideo cameras Connecting the Rear Panel Input/Output Terminal Connections Monitor ON-SCREEN Display On-Screen Display in the Time/Date and Record ModesBottom DisplayMain Menu Display Monitor ON-SCREEN DisplayOperation Alarm Input/Power Loss Data Display Hour Meter Display1Operation 4METERSetting of the Function Menu Switches Function Menu Switch SettingPreparation 3FUNCTIONSetting of the Function Menu Switches Contents of the Function Menu SwitchesIndex OFF SearchCamera SW OFF FieldAlarm/sensor Recording modeRS-232C ParameterDate and Time Setting Auto power onPreparation Cassette Loading/UnloadingSet the date and time using the Clock Adjust menu 1screen PreparationSet the date and time on the front panel display Year Month DAY Hour MinuteSelection of Record/Play Mode Mode indicationSummer Time Compensation 1During daylight savings timeRecording PreparationRecording RecordingTimer Recording Setting the daily timerVCRs display BlinkingSetting the weekly timer Start time hourCanceling timer programming To stop timer programmingTo cancel a preset timer program To cancel programmed data1Changing a preset timer program Using the VCR in the Timer Record Standby modeAlarm Recording Timelapse Alarm Recording recording Alarm signal inputAlarm RecordingStop Alarm/sensor recording mode setting screenREW 1Preparation Sensor RecordingEject Repeat Recording Check functionSeries Recording Connections1Operations Rear panelRecording with External VCR Activation Signal ConnectionOperation TerminalHow to Restore Recording After Power Failure External Timer RecordingTape End Buzzer Auto RECFunction menu switch settings Playback and SPECIAL-EFFECTS PlaybackPlayback 5To stop playbackPlayback and SPECIAL-EFFECTS Playback Special-Effects Playback1Still and field/frame advance 1Reverse playbackTracking/V. Lock Adjustment Index SearchIndex Tracking +/- button Lock +/- buttonError Indication TroubleshootingError Contents VCR operation Measures Troubleshooting No Error IndicationTop cover Installation of the SA-K97USA-K97U SA-K97U RS-232C Protocol & Commands SA-K97U SpecificationsOptional SA-K97U RS-232C Interface Board VCR control commands VCR setting commands Mode 1st byte 2nd byte1st byte 2nd byte 3rd byteCancel 67H AL/PL Reset E1HCount Reset E2H 8EHCommands for VCR status verification 1st/2nd byte3rd byte 5th byte 4th byte 6th byteContents of 5th byte BIT 0/1/2/3 Speed Code 4th byteOthers Input data correction/Error cancellation Commands reference chartAppendixes Tape Reel Counter/Tape Remaining Time TableAppendixes Rear Panel’s Input/OutputSpecifications Victor Company of JAPAN, Limited