JVC SR-9240EK appendix Sensor Recording, 1Preparation, Eject

Page 34

7 RECORDING

7-5 Sensor Recording

Sensor recording is executed only when the VCR is in the Stop mode (Stop or Timer Record Standby mode) and an alarm signal is input to the rear panel’s ALARM IN terminal.

Perform the settings for sensor recording in the same way as for "Alarm Recording" on page 33.

The mechanism of the SR-9240E/EK cannot be guaranteed if the sensor recording function is used frequently (100 times/ day or more). If alarm inputs are frequent, use the alarm recording function instead and carry out regular maintenance/ inspection and parts replacement.

1Preparation

Connect an alarm sensor to the rear panel’s alarm input terminal.

Press the [OPERATE] button to turn the operating mode on.

Setting the function menu switches for the Sensor

2Record mode

Press the [MENU] button to display the main menu

3screen.

Press the [SHIFT +/-] button to select <FUNCTION> and press the [SET +/-] button.

[ The function menu switch setting screen is 4 displayed.

Press the [SHIFT +/-] button to display the alarm/sensor

5recording mode setting screen.

Select the item to be set with the [SHIFT +/-] button. Set the value with the [SET +/-] button.

•Set the <SENSOR REC> to ON to activate the sensor recording function. The SENSOR REC indication in the display lights.

•Set the sensor recording duration.

Set <DURATION> to 5 sec., 15 sec., 30 sec., 60 sec., 120 sec., 180 sec., TAPE END or MANUAL (for as long as alarm signals are input).

*The sensor recording time will be shorter than the specified value.

*When the sensor recording time is set to MANUAL, the alarm cue signal (index code) will not be recorded correctly if alarm input lasts for less than

30 seconds.

*When sensor recording duration is set with an external switcher, set the sensor recording duration to MANUAL.

•To sound the buzzer during sensor recording, set <BUZZER> to ON.

•Set the operation mode at tape end in the case when sensor recording is executed even once with the menu switch <TAPE END MODE> on the alarm/sensor

recording mode setting screen.

STOP

: The tape stops.

REW

: The tape is rewound to the beginning and

 

stops.

REPEAT: Sensor recording continues from the

 

beginning of the tape.

EJECT

: The tape is ejected.

Sensor recording function

A LARM / SENSOR

REC MODE

 

 

Sensor recording duration

(ALARM REC)

OFF

(SENSOR REC)

ON

Buzzer

(DURATION)

180SEC

(BUZZER)

OFF

Tape end mode

(TAPE END MODE)

STOP

 

 

 

PRESS (SHIFT, SET)

 

 

PRESS (MENU) TO

END

Alarm/sensor recording mode setting screen

6After completing function menu switch setting, press the [MENU] button twice.

[ The normal screen is restored.

Check the time and data shown on the monitor's on- screen display.

If the time and date are not shown on the monitor or if you need to change the display position, use the

7<POSITION> function menu switch.

•When an alarm signal is input to the rear panel's ALARM IN terminal, recording starts automatically in the specified record mode and the AL indication is lit.

•After the specified recording duration expires, recording stops and the Stop mode is engaged.

*Because sensor recording starts from the Stop mode, it takes several seconds from the time an alarm input is received to the time recording actually

8starts.

To stop sensor recording and clear the AL indication,

9press the [AL/PL RESET] button.

To disable sensor recording, set menu switch <SENSOR REC> to OFF.

During playback, there may be some noise or picture distortion at the point where one sensor recording stops and another starts. This is not a malfunction.

35

Page 33 Page 35
Image 34
Page 33 Page 35
Contents SR-9240EK Connection to the mains supply Safety PrecautionsFor Your Safety Australia DanishOperation Lock Lock indicator Time Mode buttonButton Contents Periodical Maintenance Major FeaturesIntroduction Introduction PrecautionsDaily Inspection Controls and Connectors Front PanelControls and Connectors Display Rear Panel Clock reset signal input Series recording signal inputVCR activation signal input Connecting the wires to the terminals 9 toConnecting to a Camera ConnectionsConnections Connecting a System Using a Sequential SwitcherVideo cameras Connecting the Rear Panel Input/Output Terminal Connections Bottom Monitor ON-SCREEN DisplayOn-Screen Display in the Time/Date and Record Modes DisplayMain Menu Display Monitor ON-SCREEN DisplayOperation 1Operation Alarm Input/Power Loss Data DisplayHour Meter Display 4METERPreparation Setting of the Function Menu SwitchesFunction Menu Switch Setting 3FUNCTIONSetting of the Function Menu Switches Contents of the Function Menu SwitchesCamera SW OFF Index OFFSearch FieldRS-232C Alarm/sensorRecording mode ParameterPreparation Date and Time SettingAuto power on Cassette Loading/UnloadingSet the date and time on the front panel display Set the date and time using the Clock Adjust menu 1screenPreparation Year Month DAY Hour MinuteSummer Time Compensation Selection of Record/Play ModeMode indication 1During daylight savings timeRecording PreparationRecording RecordingTimer Recording Setting the daily timerVCRs display BlinkingSetting the weekly timer Start time hourTo cancel a preset timer program Canceling timer programmingTo stop timer programming To cancel programmed data1Changing a preset timer program Using the VCR in the Timer Record Standby modeAlarm Alarm RecordingTimelapse Alarm Recording recording Alarm signal input RecordingStop Alarm/sensor recording mode setting screenREW 1Preparation Sensor RecordingEject Repeat Recording Check function1Operations Series RecordingConnections Rear panelOperation Recording with External VCR Activation SignalConnection TerminalTape End Buzzer How to Restore Recording After Power FailureExternal Timer Recording Auto RECPlayback Function menu switch settingsPlayback and SPECIAL-EFFECTS Playback 5To stop playback1Still and field/frame advance Playback and SPECIAL-EFFECTS PlaybackSpecial-Effects Playback 1Reverse playbackIndex Tracking/V. Lock AdjustmentIndex Search Tracking +/- button Lock +/- buttonError Indication TroubleshootingError Contents VCR operation Measures Troubleshooting No Error IndicationTop cover Installation of the SA-K97USA-K97U SA-K97U RS-232C Protocol & Commands SA-K97U SpecificationsOptional SA-K97U RS-232C Interface Board VCR control commands 1st byte 2nd byte VCR setting commandsMode 1st byte 2nd byte 3rd byteCount Reset E2H Cancel 67HAL/PL Reset E1H 8EH3rd byte 5th byte Commands for VCR status verification1st/2nd byte 4th byte 6th byteContents of 5th byte BIT 0/1/2/3 Speed Code 4th byteOthers Input data correction/Error cancellation Commands reference chartAppendixes Tape Reel Counter/Tape Remaining Time TableAppendixes Rear Panel’s Input/OutputSpecifications Victor Company of JAPAN, Limited
Top Page Image Contents