JVC Model HR-J660EK Select Preset to Watch, SET Counter Display, Reset Counter, Engage ITR Mode

Page 11

 

 

 

DISPLAY

 

 

 

DISPLAY

STANDBY/ON

 

 

 

 

TIMER

 

 

VIDEO(MONO)L –AUDIO– R

REC LINK

 

TV PROG

 

 

TV

PROG

 

 

RECORD

 

 

 

11

Record One Programme While Watching Another

SELECT PRESET TO WATCH

1 Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you wish to view.

The programme selected with the TV’s preset controls appears on the TV screen while the one selected with the recorder's TV PROG buttons is recorded on the tape.

Elapsed Recording Time Indication

You can check the exact time of a recording.

1 2 3

4 5 6

7 8 9

00000

1

?

3

–:–

2

4

TV PROG

 

1

 

SET COUNTER DISPLAY

 

 

Press DISPLAY (or –:–) until a counter reading

 

 

appears on the dispay panel.

 

2

 

RESET COUNTER

 

 

Press 0000 before starting recording or playback.

 

 

 

 

 

The counter is reset to “0:00:00” and shows the exact

 

 

elapsed time as the tape runs.

Instant Timer Recording (ITR)

This easy method allows you to record for any length of time from 30 mins. to 6 hours (selectable in 30-min. increments), and shuts off the recorder after recording is finished.

START RECORDING

1 Press RECORD on the recorder.

ENGAGE ITR MODE

Tape Remaining Time

DISPLAY REMAINING TIME

1 Press DISPLAY (or –:–) until the time remaining on the tape appears.

The display panel shows the tape remaining time with

" " displayed.

By pressing the DISPLAY (or –:–) button, you can change the display to show the counter reading, preset position*, clock time or tape remaining time.

*Preset position is not displayed during playback.

NOTE:

Depending on the type of tape used, there may be times when the tape remaining time reading may not appear right away, or is not correct. "– –:– –" may sometimes appear, or the display may blink on occasion.

2 Press RECORD again. "" blinks and “0:30” appears on the front display panel.

SET RECORDING

DURATION

3 If you want to record for more than 30 minutes, press RECORD to extend the time. Each press extends recording time by 30 minutes.

NOTE:

You can only perform ITR using the RECORD button on the recorder's front panel.

Image 11
Contents HR-J665EK HR-J660EK HR-J665ES Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVGo to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointSearch PlaybackActivate SLOW-MOTION Playback Activate HIGH-SPEED SearchRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeVideo Plus+ Timer Programming Press SP/LP Timer WarningPDC Recording Satellite Receiver UsersExpress Timer Programming Press TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Skip Over Unwanted Looking For Scene You WantActivate Index Search Activate Instant ReviewS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Adjust Tracking Access Main MenuAccess Mode SET Select Picture Control SET ModeDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionSatellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording Outdoor Unit Satellite CableBefore performing the following steps Engage Auto Satellite Prog REC ModePress SP/LP on the remote control to set the tape speed Make Connections SET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto Timer Select ModeAuto SP→LP Timer Next Function Memory Activate RepeatRepeat Playback Ntsc PlaybackAudio Cable not provided Speaker Connection To Stereo SystemSET Video Channel Access Video CHAN- NEL SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Access Video Chan NEL SET ModeAuto Channel Set Tuner SetPerform Auto Chan NEL SETIs displayed on the screen Screen preset positionsProcedures After Scan CompletedStoring Channels Manually Position Change Station PresetDelete a Channel Close Confirmation Access Manual Channel SET ScreenSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetEnter Guide Prog Number Video Plus+ SetupAccess Initial SET Screen Access Guide Prog SET ScreenWhat happens if the tape runs out during recording? Questions And AnswersRemain lit on the display panel. Is there Problem? Troubleshooting Camcorder recording is not possible Re-perform the clock and/or timer settingsFront View IndexE.S.T. Picture System Display lights from bottom to AV2 IN/DECODER Connector enables connectionSymbolic Mode Indicators Programme Time Indicators show the programmeRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoVHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical IN/OUT x 1, IN/DECODER x