JVC Model HR-J660EK Engage Auto Satellite Prog REC Mode, Before performing the following steps

Page 23

DISPLAY

STANDBY/ON

 

TIMER

 

VIDEO(MONO)L –AUDIO– R

REC LINK

TV PROG

REC

LINK

 

1 2 3

2

4 5 6

7 8 9

23

Before performing the following steps:

Make sure the satellite receiver is connected to the recorder's AV2 IN/DECODER connector. (pg. 22)

Programme the timer on the satellite receiver.

Insert a cassette with the safety tab in place.

SET TAPE SPEED

1 Press SP/LP () on the remote control to set the tape speed.

ENGAGE AUTO SATELLITE

PROG REC MODE

2 Press and hold REC LINK for about 2 seconds. The indicator lights up and the recorder turns off automati- cally.

To disengage the Auto Satellite Prog Rec mode, press REC LINK. The indicator goes off.

If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

0

4

SP/LP

1

?

3

NOTES:

ATTENTION

Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.

If you have connected another appliance other than a satellite receiver to the AV2 IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

Auto Satellite Prog recording and timer-recording cannot be done at the same time.

When you press and hold the recorder's REC LINK button to engage the Auto Satellite Prog Rec mode, if the REC LINK indicator does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*.

If this is the case, perform "Express Timer Programming" (pg.14) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.

Auto Satellite Prog recording is possible with the AV2 IN/DECODER connector only.

When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function (pg. 17).

For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.

The REC LINK indicator blinks while Auto Satellite Prog recording is in progress.

Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode.

If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 1 will apply to all the programmes for Auto Satellite Prog recording.

The B.E.S.T. system (pg. 18) does not work while Auto Satellite Prog recording is in progress.

Just Clock (pg. 39) does not work when the Auto Satellite Prog Rec mode is engaged.

Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme.

If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 IN/DECODER connector.

Image 23
Contents HR-J665EK HR-J660EK HR-J665ES Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVGo to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointSearch PlaybackActivate SLOW-MOTION Playback Activate HIGH-SPEED SearchRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeVideo Plus+ Timer Programming Press SP/LP Timer WarningPDC Recording Satellite Receiver UsersExpress Timer Programming Press TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Skip Over Unwanted Looking For Scene You WantActivate Index Search Activate Instant ReviewS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Adjust Tracking Access Main MenuAccess Mode SET Select Picture Control SET ModeDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionSatellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording Outdoor Unit Satellite CableBefore performing the following steps Engage Auto Satellite Prog REC ModePress SP/LP on the remote control to set the tape speed Make Connections SET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto Timer Select ModeAuto SP→LP Timer Next Function Memory Activate RepeatRepeat Playback Ntsc PlaybackAudio Cable not provided Speaker Connection To Stereo SystemSET Video Channel Access Video CHAN- NEL SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Access Video Chan NEL SET ModeAuto Channel Set Tuner SetPerform Auto Chan NEL SETIs displayed on the screen Screen preset positionsProcedures After Scan CompletedStoring Channels Manually Position Change Station PresetDelete a Channel Close Confirmation Access Manual Channel SET ScreenSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetEnter Guide Prog Number Video Plus+ SetupAccess Initial SET Screen Access Guide Prog SET ScreenWhat happens if the tape runs out during recording? Questions And AnswersRemain lit on the display panel. Is there Problem? Troubleshooting Camcorder recording is not possible Re-perform the clock and/or timer settingsFront View IndexE.S.T. Picture System Display lights from bottom to AV2 IN/DECODER Connector enables connectionSymbolic Mode Indicators Programme Time Indicators show the programmeRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoVHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical IN/OUT x 1, IN/DECODER x