JVC Model HR-J660EK Access Main Menu, Access Mode SET, Select Picture Control SET Mode, Manually

Page 20

20ADVANCEDOPERATIONS(cont.)

Playback Pic- ture Adjustment

Picture Control

This feature helps you to adjust the playback picture quality according to your preference. *The default setting is "AUTO."

ACCESS MAIN MENU

SCREEN

1

MENU

0

?

3

4

TV PROG

OK

1 Press MENU.

 

 

ACCESS MODE SET

 

SCREEN

 

 

Move the highlighted bar (pointer) to "MODE SET" by

2 pressing %Þ, then press OK or #.

 

 

SELECT PICTURE

 

3

CONTROL SET MODE

Move the highlighted bar

MODE SET

(pointer) to "PICTURE

ON

B. E. S. T.

Manual Tracking

Your video recorder is equipped with automatic tracking control. For most tapes this will automatically adjust the tracking to suit the particular tape you are playing. In some circumstances it may be necessary to make manual tracking adjustments. This is usually only associated with old or worn tapes or recordings made on old or worn recorders. If the automatic tracking control fails to operate correctly you will see noise bars across the picture as shown on the left below. To correct this you can override the automatic control and adjust the tracking manually by pressing the TV PROG buttons.

OVERRIDE AUTOMATIC TRACKING

1

Press

on the remote to engage manual tracking.

 

ADJUST TRACKING

2

MANUALLY

Press TV PROG + or – to adjust tracking.

 

RETURN TO AUTOMATIC

 

TRACKING

 

Press

on the remote to re-engage automatic

3 tracking.

 

NOTE:

CONTROL" by pressing

 

 

PICTURE CONTROL

AUTO

%Þ, then press OK or #to

AUTO TIMER

OFF

select the desired mode.

O. S. D.

ON

AUTO: Provides optimised

AUTO SP=LP TIMER

OFF

 

 

picture benefits of

 

 

B.E.S.T. Picture

[5°] =

 

System. Normally

[MENU] : EXIT

 

select AUTO.

 

 

EDIT: Minimizes picture degradation during editing

(recording and playback).

 

SOFT: Reduces image coarseness when viewing

 

overplayed tapes containing a lot of noise.

 

SHARP: Clearer, sharper-edged picture when viewing

images with lots of flat, same-coloured surfaces

such as cartoons.

 

 

NOTES:

●When you select EDIT, SHARP or SOFT, the selected mode will not change until you select again.

●When you select EDIT to dub tapes, be sure to select AUTO after you finish dubbing the tapes.

RETURN TO NORMAL

SCREEN

4 Press MENU.

NOTES:

●When B.E.S.T. is OFF, "PICTURE CONTROL" switches automatically from AUTO to NORM.

●Select EDIT when you are dubbing tapes. Refer to page 24.

When a new tape is inserted, the recorder returns to the automatic tracking mode automatically.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents HR-J665EK HR-J660EK HR-J665ES Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV Back of RecorderGo to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackPlayback Activate SLOW-MOTION PlaybackActivate HIGH-SPEED Search SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingSatellite Receiver Users Press SP/LPExpress Timer Programming SET PDC Mode Press TV Prog +/- toCheck, Cancel And Replace Programmes Looking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Access Main Menu Access Mode SETSelect Picture Control SET Mode Adjust TrackingSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackAerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Engage Auto Satellite Prog REC ModePress SP/LP on the remote control to set the tape speed SET Recording DECK’S Input Mode SET Edit ModeEdit To Or From Another Video Recorder Make ConnectionsSET RECORDER’S Input Mode Edit From a CamcorderStart Camcorder Start RecorderAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Select ModeAuto SP→LP Timer Activate Repeat Repeat PlaybackNtsc Playback Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerAccess Video CHAN- NEL SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelAccess Video Chan NEL SET Mode With RF ConnectionTuner Set Perform Auto ChanNEL SET Auto Channel SetScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Position Change Station PresetDelete a Channel Access Manual Channel SET Screen Switch StationsSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup Access Initial SET ScreenAccess Guide Prog SET Screen Enter Guide Prog NumberWhat happens if the tape runs out during recording? Questions And AnswersRemain lit on the display panel. Is there Problem? Troubleshooting Re-perform the clock and/or timer settings Camcorder recording is not possibleIndex Front ViewAV2 IN/DECODER Connector enables connection Symbolic Mode IndicatorsProgramme Time Indicators show the programme E.S.T. Picture System Display lights from bottom toRemote Control Auto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helicalIN/OUT x 1, IN/DECODER x VHF 44.5 143/143 470 MHz
Top Page Image Contents