JVC Model HR-J660EK setup guide Video Plus+ Timer Programming

Page 12

12BASICOPERATIONS(cont.)

VIDEO Plus+

Timer

Programming

Before performing VIDEO Plus+ Timer Programming:

●Make sure that the recorder's built-in clock is set properly.

●Insert a cassette with the safety tab in place. The recorder will come on automatically.

●Turn on the TV and select the VIDEO channel (or AV mode).

With VIDEO Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise.

ACCESS VIDEO PLUS+ SCREEN

1	Press PROG.	VIDEO PLUS+
	Press PROG.

		[0 – 9] =
		[+/–] : EXPRESS PROGRAMING
		[PROG] : EXIT

The front display panel looks like this:

ENTER PLUSCODE NUMBER

	Press the NUMBER keys to	VIDEO PLUS+
	enter the PlusCode	VIDEO PLUS+
	enter the PlusCode	1 2 3 4 5 6 7 8
	2 number of the programme	1 2 3 4 5 6 7 8
	2 number of the programme
	you wish to record.

●If you make a mistake, press and input the

2 1

NUMBER 4

5 PDC 7

STOP+/–

2

5

DAILY3

6

9

2

4

WEEKLY

7

correct number.	[0 – 9] =
	[ ] : DELETE
	[PROG] : EXIT

The PlusCode number you enter appears on the front display panel:

The display panel shows only a 4-digit number.

ACCESS VIDEO PLUS+ PRO-

1,6

PROG

1

?

	SP/LP	4
		4
3		OK 3,6

GRAM SCREEN

	Press OK, and the VIDEO				– P1 –
	Plus+ Program screen			VIDEO PLUS+ 123456789
3 appears (if you’re just				START		STOP
3 appears (if you’re just			21:00		= 22:00
	starting out, “P1” appears).			SP	VPS/PDC OFF

	The display panel shows the
	The display panel shows the			DATE		TV PROG
	programme start time.			DATE		TV PROG
	programme start time.		25.12		1
	Pressing	changes the				BBC 1
	display to the programme
	display to the programme			: OK
	stop time, then the date and
	preset position.

		SP

IMPORTANT

Make sure the preset position number you wish to record is displayed; if not, see "VIDEO Plus+ Setup" on page 40 and set the Guide Program number for that PlusCode number correctly.

●If the number you entered is invalid, "ERROR" appears on the screen and "Err" appears on the display panel. Press and input a valid PlusCode number.

●If the "GUIDE PROG SET" screen appears, see "ATTENTION – Regarding Guide Program Number Set" on page 13.

Image 12

Contents HR-J665EK HR-J660EK HR-J665ES Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV Back of RecorderBefore performing the following procedure, make sure that Your TV via both an RF cable and a 21-pinGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackPlayback Activate SLOW-MOTION PlaybackActivate HIGH-SPEED Search SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingSatellite Receiver Users Press SP/LPExpress Timer Programming SET PDC Mode Press TV Prog +/- toCheck, Cancel And Replace Programmes Looking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Access Main Menu Access Mode SETSelect Picture Control SET Mode Adjust TrackingSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackAerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitEngage Auto Satellite Prog REC Mode Press SP/LP on the remote control to set the tape speedBefore performing the following steps SET Recording DECK’S Input Mode SET Edit ModeEdit To Or From Another Video Recorder Make ConnectionsSET RECORDER’S Input Mode Edit From a CamcorderStart Camcorder Start RecorderAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsSelect Mode Auto SP→LP TimerAuto Timer Activate Repeat Repeat PlaybackNtsc Playback Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerAccess Video CHAN- NEL SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelAccess Video Chan NEL SET Mode With RF ConnectionTuner Set Perform Auto ChanNEL SET Auto Channel SetScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Change Station Preset Delete a ChannelPosition Access Manual Channel SET Screen Switch StationsSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup Access Initial SET ScreenAccess Guide Prog SET Screen Enter Guide Prog NumberQuestions And Answers Remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Re-perform the clock and/or timer settings Camcorder recording is not possibleIndex Front ViewAV2 IN/DECODER Connector enables connection Symbolic Mode IndicatorsProgramme Time Indicators show the programme E.S.T. Picture System Display lights from bottom toRemote Control Auto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helicalIN/OUT x 1, IN/DECODER x VHF 44.5 143/143 470 MHz