JVC Model HR-J660EK setup guide Recording, Playback, Or press Record on the recorder

Page 19

Recording

1

START RECORDING

Press and hold RECORD and press PLAY on the remote,

or press RECORD on the recorder.

DURING B.E.S.T.

 

 

 

 

B.E.S.T. COMPLETE

The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording.

NOTES:

The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

The B.E.S.T. system does not work while Auto Satellite Prog recording is in progress (pg. 22).

In the case of timer recording, the B.E.S.T. system works before recording is initiated.

Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re- performed.

Pressing the recorder's RECORD button while "BEST" is displayed does not start Instant Timer Recording

(pg. 11).

ATTENTION

Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after RECORD and PLAY on the remote are pressed, or RECORD on the recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps:

1)Press and hold PAUSE and press RECORD to engage the RECORD PAUSE mode.

The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, re- enters RECORD PAUSE.

2)Press PLAY when you are ready to start recording.

If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” in step 4 on page 18.

19

Playback

The recorder assesses the quality of the tape once you initiate playback.

START PLAYBACK

1 Press PLAY.

The recorder adjusts the playback picture quality based on the quality of the tape in use.

B.E.S.T. is active during Auto Tracking. “BEST” appears blinking on the recorder’s display panel.

NOTES:

When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well.

When watching a rental tape or one recorded on another video recorder, or when using this recorder as the player for editing, set B.E.S.T. to your preference by performing steps 1 through 5 on page 18.

"BEST" only appears at the beginning of automatic tracking. Even though it doesn't appear after that, the B.E.S.T. function is operative.

Image 19
Contents HR-J665EK HR-J660EK HR-J665ES Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVYour TV via both an RF cable and a 21-pin Before performing the following procedure, make sure thatGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointSearch PlaybackActivate SLOW-MOTION Playback Activate HIGH-SPEED SearchRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeVideo Plus+ Timer Programming Press SP/LP Timer WarningPDC Recording Satellite Receiver UsersExpress Timer Programming Press TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Skip Over Unwanted Looking For Scene You WantActivate Index Search Activate Instant ReviewTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Playback RecordingOr press Record on the recorder Adjust Tracking Access Main MenuAccess Mode SET Select Picture Control SET ModeDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionSatellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording Outdoor Unit Satellite CablePress SP/LP on the remote control to set the tape speed Engage Auto Satellite Prog REC ModeBefore performing the following steps Make Connections SET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto SP→LP Timer Select ModeAuto Timer Next Function Memory Activate RepeatRepeat Playback Ntsc PlaybackAudio Cable not provided Speaker Connection To Stereo SystemSET Video Channel Access Video CHAN- NEL SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Access Video Chan NEL SET ModeAuto Channel Set Tuner SetPerform Auto Chan NEL SETIs displayed on the screen Screen preset positionsProcedures After Scan CompletedStoring Channels Manually Delete a Channel Change Station PresetPosition Close Confirmation Access Manual Channel SET ScreenSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetEnter Guide Prog Number Video Plus+ SetupAccess Initial SET Screen Access Guide Prog SET ScreenRemain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Camcorder recording is not possible Re-perform the clock and/or timer settingsFront View IndexE.S.T. Picture System Display lights from bottom to AV2 IN/DECODER Connector enables connectionSymbolic Mode Indicators Programme Time Indicators show the programmeRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoVHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical IN/OUT x 1, IN/DECODER x