JVC Model HR-J660EK Questions And Answers, What happens if the tape runs out during recording?

Page 41

SUBSIDIARYINFORMATION

41

Questions And Answers

PLAYBACK

Q. What happens if the end of the tape is reached during playback or search?

A.The tape is automatically rewound to the beginning.

Q.Can the video recorder indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.During search, slow, still and frame-by-frame playback, I can’t hear any audio. What’s the problem?

A.This is normal.

Q.When returning from variable-speed search to normal playback, the picture is disturbed. Should I be concerned about this?

A.No, it is normal.

Q.Noise bars appear during variabl-speed search. What’s the problem?

A.This is normal.

Q.Other than preventing further recording, what effect does removing the Record Safety tab have?

A.It disables marking of index codes.

Q.Sometimes, during Index Search, the video recorder can’t find the programme I want to see. Why not?

A.There may be index codes too close together.

RECORDING

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?

A.This is normal. It reduces distortion at the pause and resume points.

Q.Can the video recorder indefinitely remain in the Record-Pause mode?

A.No. The video recorder shuts off automatically after 5 minutes to protect the heads.

Q.What happens if the tape runs out during recording?

A.The video recorder automatically rewinds it to the beginning or, if Timer Recording, the cassette is ejected.

TIMER RECORDING

Q. "" and " " remain lit on the display panel. Is there

a problem?

A.No. This is a normal condition for a timer recording in progress.

Q.Can I programme the timer while I’m watching a tape or a TV broadcast?

A.You won’t see the picture as it is replaced by the on- screen menu, but the audio from the program or tape you’re viewing can be heard.

Q.Is it possible to timer-record a TV programme broadcast in 2000?

A.Yes, it is possible.

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 41
Contents HR-J665EK HR-J660EK HR-J665ES Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVGo to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate SLOW-MOTION Playback PlaybackActivate HIGH-SPEED Search SearchRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningSatellite Receiver Users Press SP/LPExpress Timer Programming Press TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Activate Index Search Looking For Scene You WantActivate Instant Review Skip Over UnwantedS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Access Mode SET Access Main MenuSelect Picture Control SET Mode Adjust TrackingReceiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackAutomatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Engage Auto Satellite Prog REC ModePress SP/LP on the remote control to set the tape speed SET Edit Mode SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Make ConnectionsEdit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Select ModeAuto SP→LP Timer Repeat Playback Activate RepeatNtsc Playback Next Function MemoryAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video CHAN- NEL SET ModeVideo Channel Set SET Video ChannelWith RF Connection Access Video Chan NEL SET ModePerform Auto Chan Tuner SetNEL SET Auto Channel SetProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Position Change Station PresetDelete a Channel Switch Stations Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetAccess Initial SET Screen Video Plus+ SetupAccess Guide Prog SET Screen Enter Guide Prog NumberWhat happens if the tape runs out during recording? Questions And AnswersRemain lit on the display panel. Is there Problem? Troubleshooting Camcorder recording is not possible Re-perform the clock and/or timer settingsFront View IndexSymbolic Mode Indicators AV2 IN/DECODER Connector enables connectionProgramme Time Indicators show the programme E.S.T. Picture System Display lights from bottom toRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoDA4 Double Azimuth helical Maximum recording timeIN/OUT x 1, IN/DECODER x VHF 44.5 143/143 470 MHz