JVC Model HR-J660EK setup guide Access Video Chan NEL SET Mode, With RF Connection

Page 31

DISPLAY

STANDBY/ON

	TIMER
VIDEO(MONO)L –AUDIO– R	REC LINK	TV PROG

STOP

31

With RF Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■the connected TV is turned on.

■batteries have been installed in the remote control.

ACCESS VIDEO CHAN-

NEL SET MODE

1 Press and hold down STOP on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

1 2 3

4 5 6

7 8 9

0

1

?

2

4

TV PROG

OK

2 Press TV PROG+ or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area. Refer to list on page 38 for details of broadcast stations in your area.

(Ex.) If channel 36 is available in your area

Then set your TV to UHF channel 36. (Refer to the instructions supplied with your TV set for how to do this.)

●If the two vertical white bars appear clearly on the screen as shown in the illustration at bottom left, go to step 3.

●If the two vertical white bars do not appear clearly, re- set the video recorder to another vacant channel and try again.

IMPORTANT

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET MODE

TEST SIGNAL

The channel on which the screen on the left appears clearly in step 2 is your Video Channel.

3 Press OK.

To view picture signals from the video recorder, set your TV to the Video Channel.

Image 31

Contents HR-J665EK HR-J660EK HR-J665ES Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVYour TV via both an RF cable and a 21-pin Before performing the following procedure, make sure thatGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointSearch PlaybackActivate SLOW-MOTION Playback Activate HIGH-SPEED SearchRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeVideo Plus+ Timer Programming Press SP/LP Timer WarningPDC Recording Satellite Receiver UsersExpress Timer Programming Press TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Skip Over Unwanted Looking For Scene You WantActivate Index Search Activate Instant ReviewTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Playback RecordingOr press Record on the recorder Adjust Tracking Access Main MenuAccess Mode SET Select Picture Control SET ModeDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionSatellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording Outdoor Unit Satellite CablePress SP/LP on the remote control to set the tape speed Engage Auto Satellite Prog REC ModeBefore performing the following steps Make Connections SET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto SP→LP Timer Select ModeAuto Timer Next Function Memory Activate RepeatRepeat Playback Ntsc PlaybackAudio Cable not provided Speaker Connection To Stereo SystemSET Video Channel Access Video CHAN- NEL SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Access Video Chan NEL SET ModeAuto Channel Set Tuner SetPerform Auto Chan NEL SETIs displayed on the screen Screen preset positionsProcedures After Scan CompletedStoring Channels Manually Delete a Channel Change Station PresetPosition Close Confirmation Access Manual Channel SET ScreenSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetEnter Guide Prog Number Video Plus+ SetupAccess Initial SET Screen Access Guide Prog SET ScreenRemain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Camcorder recording is not possible Re-perform the clock and/or timer settingsFront View IndexE.S.T. Picture System Display lights from bottom to AV2 IN/DECODER Connector enables connectionSymbolic Mode Indicators Programme Time Indicators show the programmeRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoVHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical IN/OUT x 1, IN/DECODER x