JVC SR-9168U appendix Monitor ON-SCREEN Display, Main Menu Display, Operation

Page 15

4 MONITOR ON-SCREEN DISPLAY

4-2 Main Menu Display

You can display date and time data recorded when an alarm input or power failure occurs, as well as the hour meter (drum rotating time) by selecting the desired item in the main menu.

The timer recording program setting screen, function menu switch setting screen, and date/time setting screen can also be displayed by selecting the desired item in the main menu.

[MENU] button

[SHIFT +/–] buttons

 

 

 

 

 

 

 

SR-9168U

VIDEO CASSETTE RECORDER

 

 

 

OPERATE

COUNT/

MENU

SHIFT/TRACKING

RESET

 

CLOCK

 

/CANCEL

OPE. LOCK

TIME

TIMER

SET/V.LOCK

AL/PL

 

MODE

REC

 

RESET

ON

[SET +/–] buttons

Main menu screen

MAIN MENU

PROGRAM TIMER

FUNCTION

ALARM IN

POWER LOSS

HOUR METER

CLOCK ADJUST

PRESS (SHIFT, SET)

PRESS (MENU) TO END

PROGRAM TIMER:

Displays the program setting screen for timer recording.

*Timer programming is not possible if the date and time are not set. In this case, the date/time setting screen will be displayed.

FUNCTION:

Displays the function menu setting screen.

ALARM IN:

Displays the date and time when an alarm signal was input.

POWER LOSS

Displays the date and time when a power failure occurred.

HOUR METER:

Displays the hour meter (drum rotating time).

CLOCK ADJUST:

Displays the date/time setting screen.

*Set the date and time before using this unit.

Operation

5Connect the VCR's video output connector to the monitor's video input connector.

1Turn on the VCR and the monitor. Make sure the Stop mode is engaged.

2Press the [MENU] button.

[The main menu screen is displayed.

3Press the [SHIFT +/-] button to move the cursor arrow to the item you want to display.

Press the [SHIFT +] button to move the cursor arrow down. Press the [SHIFT -] button to move it up.

4Press the [SET +] or [SET -] button to display the selected item.

5To end menu operation and restore the normal screen, press the [MENU] button.

When the [MENU] button is pressed during playback, the monitor screen display switches from the playback picture to the input video signal (EE picture) and the main menu is shown on the screen.

This means that even during playback you can check menu contents. Press the [MENU] button again to restore the playback picture.

15

Image 15
Contents For Customer Use Video Cassette Recorder SR-9168UINSTRUCTIONSInformation Safety PrecautionsContents Introduction Major FeaturesPeriodical Maintenance Periodic MaintenancePrecautions IntroductionDaily Inspection Front Panel Controls and ConnectorsControls and Connectors Display Rear Panel Connecting the wires to the terminals 9 to Series recording signal inputVCR activation signal input Clock reset signal inputConnections Connecting to a CameraVideo cameras Connecting a System Using a Sequential SwitcherVideo output Camera Sequential switcher ConnectionsConnecting the Rear Panel Input/Output Terminal Connections Display Position settingMonitor ON-SCREEN Display On-Screen Display in the Time/Date and Record ModesMonitor ON-SCREEN Display Main Menu DisplayOperation SET +/- buttons button Alarm Input/Power Loss Data DisplayHour Meter Display Menu buttonPreparation Function Menu Switch SettingContents of the Function Menu Switches Setting of the Function Menu SwitchesField Index OFFSearch Camera SW OFFAlarm/sensor Parameter SettingRS-232C Cassette Loading/Unloading Date and Time SettingAuto power on PreparationSet the date and time on the front panel display Set the date and time using the Clock Adjust menu screenDate/time setting screen PreparationDuring daylight savings time Selection of Record/Play ModeMode indication Summer Time CompensationPreparation RecordingRecording RecordingSetting the daily timer Timer RecordingBlinking VCRs displaySetting the weekly timer To stop timer programming Cancel program setting screenCanceling timer programming To cancel programmed dataUsing the VCR in the Timer Record Standby mode Changing a preset timer programRecording Alarm RecordingAlarm recording will not start from the Pause mode 6H EP,18HPress the Operate button to turn the operating mode on Tape stopsStops Beginning of the tape Recording mode setting screenSensor Recording Repeat Sensor recording continues fromAuto Recording Check function Repeat RecordingRear panel Series RecordingConnections OperationsOperation Recording with External VCR Activation SignalVCR control signal ground signal ConnectionTape End Buzzer How to Restore Recording After Power FailureExternal Timer Recording VTR mode 1 setting screenTo stop playback Function menu switch settingsSet to on to search the alarm-recorded positions index code PlaybackReverse playback Playback and SPECIAL-EFFECTS PlaybackSpecial-Effects Playback Still and field by field advanceIndex Tracking/V. Lock AdjustmentIndex Search Press the V. Lock +/- button to minimize vertical jitterTroubleshooting Error IndicationError Contents VCR operation Measures No Error Indication TroubleshootingInstallation of the SA-K97U Parity check Stop bit Bit SA-K97U SpecificationsPin no Signals Operations Direction of signals Optional SA-K97U RS-232C Interface BoardSA-K97U RS-232C Protocol & Commands JVC base tableJVC VCR control commands This section provides technical data for programmers3rd byte VCR setting commandsMode 1st byte 2nd byte 1st byte 2nd byte8EH Cancel 67HAL/PL Reset E1H Count Reset E2H4th byte 6th byte Commands for VCR status verification1st/2nd byte 3rd byte 5th byte4th byte Contents of 5th byte BIT 0/1/2/3 Speed CodeCommands reference chart Others Input data correction/Error cancellationRear Panel’s Input/Output AppendixesAppendixes SpecificationsVictor Company of JAPAN, Limited SR-9168U Video Cassette Recorder