JVC SR-9168U appendix Controls and Connectors, Front Panel

Page 6

2 CONTROLS AND CONNECTORS

2-1 Front Panel

5 4 3

REC STOP/EJECT REC

CHECK

PAUSE/

REVERSE STILL PLAY

REWFF

2

11

12

14

1

 

 

SR-9168U

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VIDEO CASSETTE RECORDER

OPERATE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COUNT/

MENU

SHIFT/TRACKING

RESET

 

CLOCK

 

/CANCEL

OPE. LOCK

 

 

 

 

TIME

TIMER

SET/V.LOCK

AL/PL

 

MODE

REC

 

RESET

ON

6

7

1[OPERATE] button

Press to turn the operating power ON/OFF. When this button is ON, the OPERATE indicator lights and the unit can be operated. When a cassette is inserted, the power switches on and the OPERATE indicator lights automatically.

The OPERATE button does not completely shut off the mains power to the unit, but switches the operating current on and off.

2Cassette loading slot

For cassette loading and unloading. Use a VHS cassette tape.

3[REC CHECK] button Use to check recording.

When pressed in the Record mode, this will rewind the tape about 5 seconds and then play back the rewound section so that the recording quality can be checked.

After playback, the Record mode is automatically re- engaged at the point where recording was interrupted.

•The FM level is checked during playback in Recording Check operation to determine whether or not picture quality is defective. If it is judged defective, the heads are automatically cleaned. How this operation is

performed is determined by the setting of the [REC CHECK] switch in the function menu.

–When set to "MANUAL":

Head cleaning is performed once and recording resumes.

–When set "AUTO":

Head cleaning is performed once and recording is resumed for several seconds. Then, Recording Check operation is performed again.

If picture quality is again judged defective, head cleaning is performed once again and "E-09" is shown on the display to indicate that there is a problem. Recording will continue, however.

8

9

10

13

15

16

4[STOP/EJECT] button

•Stops the tape.

•Ejects the tape when pressed in the Stop mode.

5[REC] button

Starts recording when pressed in the Stop mode.

6Operation buttons [PLAY] button Starts playback.

[PAUSE/STILL] button

•Temporarily stops recording when pressed in the Record mode.

•Displays a still picture when pressed in the Play mode.

•Advances field by field when pressed in the Still mode.

[REVERSE] button

Starts reverse playback when pressed in the Play or Still mode.

[FF] button

•Fast forwards the tape.

•Starts fast-forward shuttle search when pressed in the Play mode.

•If the function menu switch <INDEX SEARCH> is set to ON and an alarm-recorded tape is loaded, Index (alarm) Search starts in the forward direction when this button is pressed in the Stop or Play mode.

[REW] button

•Rewinds the tape.

•Starts reverse shuttle search when pressed in the Play mode.

•If the function menu switch <INDEX SEARCH> is set to ON and an alarm-recorded tape is loaded, Index (alarm) Search starts in the reverse direction when this button is pressed in the Stop or Play mode.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Video Cassette Recorder SR-9168UINSTRUCTIONS For Customer UseSafety Precautions InformationContents Periodic Maintenance Major FeaturesPeriodical Maintenance IntroductionPrecautions IntroductionDaily Inspection Controls and Connectors Front PanelControls and Connectors Display Rear Panel Clock reset signal input Series recording signal inputVCR activation signal input Connecting the wires to the terminals 9 toConnecting to a Camera ConnectionsConnections Connecting a System Using a Sequential SwitcherVideo output Camera Sequential switcher Video camerasConnecting the Rear Panel Input/Output Terminal Connections On-Screen Display in the Time/Date and Record Modes Position settingMonitor ON-SCREEN Display DisplayMonitor ON-SCREEN Display Main Menu DisplayOperation Menu button Alarm Input/Power Loss Data DisplayHour Meter Display SET +/- buttons buttonFunction Menu Switch Setting PreparationSetting of the Function Menu Switches Contents of the Function Menu SwitchesCamera SW OFF Index OFFSearch FieldAlarm/sensor Parameter SettingRS-232C Preparation Date and Time SettingAuto power on Cassette Loading/UnloadingPreparation Set the date and time using the Clock Adjust menu screenDate/time setting screen Set the date and time on the front panel displaySummer Time Compensation Selection of Record/Play ModeMode indication During daylight savings timeRecording PreparationRecording RecordingTimer Recording Setting the daily timerVCRs display BlinkingSetting the weekly timer To cancel programmed data Cancel program setting screenCanceling timer programming To stop timer programmingChanging a preset timer program Using the VCR in the Timer Record Standby mode6H EP,18H Alarm RecordingAlarm recording will not start from the Pause mode RecordingPress the Operate button to turn the operating mode on Tape stopsStops Repeat Sensor recording continues from Recording mode setting screenSensor Recording Beginning of the tapeRepeat Recording Auto Recording Check functionOperations Series RecordingConnections Rear panelConnection Recording with External VCR Activation SignalVCR control signal ground signal OperationVTR mode 1 setting screen How to Restore Recording After Power FailureExternal Timer Recording Tape End BuzzerPlayback Function menu switch settingsSet to on to search the alarm-recorded positions index code To stop playbackStill and field by field advance Playback and SPECIAL-EFFECTS PlaybackSpecial-Effects Playback Reverse playbackPress the V. Lock +/- button to minimize vertical jitter Tracking/V. Lock AdjustmentIndex Search IndexTroubleshooting Error IndicationError Contents VCR operation Measures Troubleshooting No Error IndicationInstallation of the SA-K97U Optional SA-K97U RS-232C Interface Board SA-K97U SpecificationsPin no Signals Operations Direction of signals Parity check Stop bit BitSA-K97U RS-232C Protocol & Commands JVC base tableJVC This section provides technical data for programmers VCR control commands1st byte 2nd byte VCR setting commandsMode 1st byte 2nd byte 3rd byteCount Reset E2H Cancel 67HAL/PL Reset E1H 8EH3rd byte 5th byte Commands for VCR status verification1st/2nd byte 4th byte 6th byteContents of 5th byte BIT 0/1/2/3 Speed Code 4th byteOthers Input data correction/Error cancellation Commands reference chartAppendixes Rear Panel’s Input/OutputSpecifications AppendixesSR-9168U Video Cassette Recorder Victor Company of JAPAN, Limited
Top Page Image Contents