JVC SR-9168U appendix Safety Precautions, Information

Page 2

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INDIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This unit should be used with 120 V AC only.

CAUTION:

To prevent electric shocks and fire hazards, do NOT use any other power source.

NOTE:

The rating plate (serial number plate) is on the rear of the unit.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer- ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep- tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION

CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERA- TION.

ATTENTION

RISQUE D’ELECTROCUTION

NE PAS OUVRIR

ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION NE PAS OUVRIR LE BOITER.

AUCUNE PIECE INTERIEURE N’EST

A REGLER PAR L’UTILISATEUR.

SE REFERER A UN AGENT QUALIFIE EN CAS DE PROBLEME.

Le symbole de l’éclair à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’une “tension dangereuse” non isolée dans le boîtier du produit. Cette tension est suffisante pour provoquer l’électrocution de personnes.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’opérations d’entretien importantes au sujet desquelles des renseignements se trouvent dans le manuel d’instructions.

*Ces symboles ne sont utilisés qu’aux Etats-Unis.

AVERTISSEMENT:

POUR EVITER LES RISQUES D’INCENDIE OU D’ELECTROCUTION, NE PAS EXPOSER L’APPAREIL A L’HUMIDITE OU A LA PLUIE.

Ce magnétoscope ne doit être utilisé que sur du courant alternatif en 120 V.

ATTENTION:

Afin d’éviter tout resque d’incendie ou d’électrocution, ne pas utiliser d’autres sources d’alimentation électrique.

REMARQUE:

La plaque d’identification (numéro de série) se trouve sur le panneau arrière de l’appareil.

WARNING:

The battery used in the SR-9168U must be replaced at the JVC authorized service dealer only.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003 édictée par le ministre des Communications.

2

Image 2
Contents Video Cassette Recorder SR-9168UINSTRUCTIONS For Customer UseSafety Precautions InformationContents Periodic Maintenance Major FeaturesPeriodical Maintenance IntroductionDaily Inspection PrecautionsIntroduction Controls and Connectors Front PanelControls and Connectors Display Rear Panel Clock reset signal input Series recording signal inputVCR activation signal input Connecting the wires to the terminals 9 toConnecting to a Camera ConnectionsConnections Connecting a System Using a Sequential SwitcherVideo output Camera Sequential switcher Video camerasConnecting the Rear Panel Input/Output Terminal Connections On-Screen Display in the Time/Date and Record Modes Position settingMonitor ON-SCREEN Display DisplayOperation Monitor ON-SCREEN DisplayMain Menu Display Menu button Alarm Input/Power Loss Data DisplayHour Meter Display SET +/- buttons buttonFunction Menu Switch Setting PreparationSetting of the Function Menu Switches Contents of the Function Menu SwitchesCamera SW OFF Index OFFSearch FieldRS-232C Alarm/sensorParameter Setting Preparation Date and Time SettingAuto power on Cassette Loading/UnloadingPreparation Set the date and time using the Clock Adjust menu screenDate/time setting screen Set the date and time on the front panel displaySummer Time Compensation Selection of Record/Play ModeMode indication During daylight savings timeRecording PreparationRecording RecordingTimer Recording Setting the daily timerVCRs display BlinkingSetting the weekly timer To cancel programmed data Cancel program setting screenCanceling timer programming To stop timer programmingChanging a preset timer program Using the VCR in the Timer Record Standby mode6H EP,18H Alarm RecordingAlarm recording will not start from the Pause mode RecordingStops Press the Operate button to turn the operating mode onTape stops Repeat Sensor recording continues from Recording mode setting screenSensor Recording Beginning of the tapeRepeat Recording Auto Recording Check functionOperations Series RecordingConnections Rear panelConnection Recording with External VCR Activation SignalVCR control signal ground signal OperationVTR mode 1 setting screen How to Restore Recording After Power FailureExternal Timer Recording Tape End BuzzerPlayback Function menu switch settingsSet to on to search the alarm-recorded positions index code To stop playbackStill and field by field advance Playback and SPECIAL-EFFECTS PlaybackSpecial-Effects Playback Reverse playbackPress the V. Lock +/- button to minimize vertical jitter Tracking/V. Lock AdjustmentIndex Search IndexError Contents VCR operation Measures TroubleshootingError Indication Troubleshooting No Error IndicationInstallation of the SA-K97U Optional SA-K97U RS-232C Interface Board SA-K97U SpecificationsPin no Signals Operations Direction of signals Parity check Stop bit BitJVC SA-K97U RS-232C Protocol & CommandsJVC base table This section provides technical data for programmers VCR control commands1st byte 2nd byte VCR setting commandsMode 1st byte 2nd byte 3rd byteCount Reset E2H Cancel 67HAL/PL Reset E1H 8EH3rd byte 5th byte Commands for VCR status verification1st/2nd byte 4th byte 6th byteContents of 5th byte BIT 0/1/2/3 Speed Code 4th byteOthers Input data correction/Error cancellation Commands reference chartAppendixes Rear Panel’s Input/OutputSpecifications AppendixesSR-9168U Video Cassette Recorder Victor Company of JAPAN, Limited