JVC SR-9168U Index OFF, Search, Camera SW OFF, Field, Frame OFF, Tape END OFF, Buzzer, Sel Ext

5 SETTING OF THE FUNCTION MENU SWITCHES

5-2 Contents of the Function Menu Switches

	[	]: Factory setting
Screens	Items	Set values					Function
VTR mode 1	INDEX	[OFF]	Enables or disables the Index Search function.
setting	SEARCH	ON	OFF : The index search function is disabled.
			ON	: When an alarm-recorded tape is put in the FF or REW Shuttle Search
				mode, the VCR searches for the nearest recorded index code (VISS
				signal) and engages playback at the indexed position.
				When an alarm-recorded tape is fast-forwarded or rewound, the VCR
				searches for the nearest index code and enters the Stop mode at the
				indexed position.
	CAMERA SW	[OFF]	Sets the camera switching interval for output to an external sequential switcher
		1 FIELD	during recording.
		1 FRAME	OFF		: No camera switching signal is output.
			1 FIELD		: Set to this position to switch the camera every 1 field.
			1 FRAME: Set to this position to switch cameras every 1 frame.
	TAPE END	[OFF]	Turns the Tape End buzzer on or off.
	BUZZER	ON	OFF : The buzzer does not sound at tape end.
			ON	: When the tape reaches the position set with the <REC REMAIN> menu
				function switch during recording (tape end, or 3 minutes or 6 minutes
				before the tape ends during 6H mode ), a buzzer sounds.
				To stop the buzzer sound, press the [REW] button, [EJECT] button or
				[POWER] button.
				When the mode is changed, the buzzer sound stops.
	WARNING	[OFF]	Turns the warning buzzer on or off.
	BUZZER	ON	OFF : The buzzer does not sound.
			ON	: The buzzer sounds.
VTR mode 2	SUMMER TIME	[OFF]	Turns summer time compensation on or off.
setting		ON	OFF : Clock is not adjusted for summer (daylight saving) time.
			ON	: Clock is adjusted for summer (daylight saving) time.
	TERMINAL	[SERIES]	Select the signal to be input or output to the [SERIES/CLOCK IN·OUT]
	SEL 1	EXT	terminals on the rear panel.
		C.ADJ	SERIES : Set to this position to input or output a series recording signal.
			EXT		: Set to this position to start or stop the recording with the VCR
					activation signal input from an external control device.
			C.ADJ		: Set to this position to input or output a clock reset signal.
	TERMINAL	[WARN.]	Select the signal output from the rear panel’s [WARNING/REC OUT] terminal.
	SEL 2	REC	WARN.		: Set to this position to output a warning signal. The warning signal is
					output if an abnormality occurs in tape transport or mechanism
					operation.
			REC		: Set to this position to output a recording mode signal (+12 V) in the
					Record mode.
	REC REMAIN	[OFF]	Sets the timing to process tape end before the actual tape end. This menu
		180S	switch setting is effective in the 6H to L30H Record modes. For the 48H to
		360S	240H modes, set with <COUNT END>. The following operations are executed
			at the timing set with this menu switch.
			• The tape end signal is output from the rear panel's [TAPE END] terminal.
			• The series recording signal is output from the rear panel's [CLOCK/SERIES
			OUT] terminal (with the TERMINAL SEL 1> function menu switch set to
			"SERIES").
			• The tape end buzzer sounds (with the <TAPE END BUZZER> function menu
			switch set to "ON").
			• "End" is shown on the counter display.
			The set values (180S/360S) are for the 6H mode. The relation between the
			recording mode and the recording time is shown below.
						Setting		Record modes
							6H	L18H	L30H
						OFF	Tape end	Tape end	Tape end
						180S	3 minutes	9 minutes	15 minutes
						360S	6 minutes	18 minutes	30 minutes

These values should be used as a reference only. Actual values may differ depending on the tape used.

19