JVC SR-9168U Preparation, Set the date and time using the Clock Adjust menu screen, Main menu

Page 22

6 PREPARATION

(Main menu)

MAIN MENU

PROGRAM TIMER

FUNCTION

ALARM IN

POWER LOSS

HOUR METER

CLOCK ADJUST

PRESS (SHIFT, SET)

PRESS (MENU) TO END

[SET +/-] button

(Date/time setting screen)

CLOCK

ADJUST

YEAR

2000

MONTH

1

DAY

1

HOUR

0

MINUTE

0

PRESS (SHIFT, SET)

PRESS (MENU) TO END

 

[SHIFT +/-] button and

 

[SET +/-] button

CLOCK

ADJUST

YEAR

1999

MONTH

9

DAY

30

HOUR

17

MINUTE

30

PRESS (SHIFT, SET)

PRESS (MENU) TO END

Set the date and time using the CLOCK ADJUST menu screen.

1Turn on this unit and the monitor and engage the Stop mode.

2 Press the [MENU] button to display the main menu screen.

3 Press the [SHIFT +] or [SHIFT -]button to select <CLOCK ADJUST>. (Set the cursor arrow to <CLOCK ADJUST>.)

4 Press the [SET +] or [SET -] button to display the CLOCK ADJUST screen on the monitor.

5 Select the item to be set.

Press the [SHIFT +] or [SHIFT -] button to select the item. [The selected item will blink.

6Enter the value for the selected item with the [SET +/-] button.

Press the [SET +] button to increase the number.

Press the [SET -] button to decrease the number.

The setting range for the year is from 1997 to 2096.

This VCR uses the 24-hour clock.

If an invalid date is set, it is automatically corrected.

(e.g.) 1999-2-29 [ 1999-2-28

Repeat steps 5 and 6 until the year, month, date, hour, and minutes

have all been set.

7End date and time setting.

• Press the [MENU] button twice.

[The normal display is restored and the set date and time are shown on screen. The time count starts from 00 seconds.

[MENU] button

(Normal screen)

1 7 : 3 0 : 0 1 L24H

9 – 30 – 1999

(Menu switch <POSITION> set to L-UP)

YEAR

MONTH DAY

HOUR MINUTE

Note:

If you press the [OPERATE] button after setting the date and time without first pressing the [MENU] button, the set date and time are canceled.

Set the date and time on the front panel display

1Turn the power on.

2Press the [COUNT/CLOCK] button for at least 2 seconds.

• The “year” indication blinks in the display.

3Enter the value for the year with the [SET+] or [SET-] button.

4 Press the [SHIFT+] button: the “month” indication blinks.

Press the [SHIFT+] or [SHIFT-] button to move the blinking section.

Enter the value for the blinking section with the [SET+] or [SET-] button.

5Set the “month”, “day”, “hour” and “minute” with the [SHIFT+/-] and [SET+/-] buttons.

6When you have finished setting, press the [COUNT/CLOCK] button.

The display returns to the clock display mode and the time count starts from 00 seconds.

Time indication on the VCR's display

When the power is turned off, the time is displayed. When the power is turned on, set the time display mode with the [COUNT/CLOCK] button to display the current time.

The first time you turn on the power, the time display shows a blinking "0:00:00".

When the built-in backup battery capacity is low, the error indication E-10 appears on the display. Contact your local JVC dealer to replace the built-in battery.

22

Image 22
Contents Video Cassette Recorder SR-9168UINSTRUCTIONS For Customer UseSafety Precautions InformationContents Periodic Maintenance Major FeaturesPeriodical Maintenance IntroductionIntroduction PrecautionsDaily Inspection Controls and Connectors Front PanelControls and Connectors Display Rear Panel Clock reset signal input Series recording signal inputVCR activation signal input Connecting the wires to the terminals 9 toConnecting to a Camera ConnectionsConnections Connecting a System Using a Sequential SwitcherVideo output Camera Sequential switcher Video camerasConnecting the Rear Panel Input/Output Terminal Connections On-Screen Display in the Time/Date and Record Modes Position settingMonitor ON-SCREEN Display DisplayMain Menu Display Monitor ON-SCREEN DisplayOperation Menu button Alarm Input/Power Loss Data DisplayHour Meter Display SET +/- buttons buttonFunction Menu Switch Setting PreparationSetting of the Function Menu Switches Contents of the Function Menu SwitchesCamera SW OFF Index OFFSearch FieldParameter Setting Alarm/sensorRS-232C Preparation Date and Time SettingAuto power on Cassette Loading/UnloadingPreparation Set the date and time using the Clock Adjust menu screenDate/time setting screen Set the date and time on the front panel displaySummer Time Compensation Selection of Record/Play ModeMode indication During daylight savings timeRecording PreparationRecording RecordingTimer Recording Setting the daily timerVCRs display BlinkingSetting the weekly timer To cancel programmed data Cancel program setting screenCanceling timer programming To stop timer programmingChanging a preset timer program Using the VCR in the Timer Record Standby mode6H EP,18H Alarm RecordingAlarm recording will not start from the Pause mode RecordingTape stops Press the Operate button to turn the operating mode onStops Repeat Sensor recording continues from Recording mode setting screenSensor Recording Beginning of the tapeRepeat Recording Auto Recording Check functionOperations Series RecordingConnections Rear panelConnection Recording with External VCR Activation SignalVCR control signal ground signal OperationVTR mode 1 setting screen How to Restore Recording After Power FailureExternal Timer Recording Tape End BuzzerPlayback Function menu switch settingsSet to on to search the alarm-recorded positions index code To stop playbackStill and field by field advance Playback and SPECIAL-EFFECTS PlaybackSpecial-Effects Playback Reverse playbackPress the V. Lock +/- button to minimize vertical jitter Tracking/V. Lock AdjustmentIndex Search IndexError Indication TroubleshootingError Contents VCR operation Measures Troubleshooting No Error IndicationInstallation of the SA-K97U Optional SA-K97U RS-232C Interface Board SA-K97U SpecificationsPin no Signals Operations Direction of signals Parity check Stop bit BitJVC base table SA-K97U RS-232C Protocol & CommandsJVC This section provides technical data for programmers VCR control commands1st byte 2nd byte VCR setting commandsMode 1st byte 2nd byte 3rd byteCount Reset E2H Cancel 67HAL/PL Reset E1H 8EH3rd byte 5th byte Commands for VCR status verification1st/2nd byte 4th byte 6th byteContents of 5th byte BIT 0/1/2/3 Speed Code 4th byteOthers Input data correction/Error cancellation Commands reference chartAppendixes Rear Panel’s Input/OutputSpecifications AppendixesSR-9168U Video Cassette Recorder Victor Company of JAPAN, Limited