JVC hr-dvs3u manual 36 EN, Select the DV deck, Press DV

Page 36

36 EN

PLAYBACK/RECORDING ON DV DECK

Basic Playback

(DV deck)

Turn on the TV and select the AV mode.

1

3

2

T

W

1 2 3

2

4 5 6

7 8 9

04

1

DV

S-VHS

ALoad a cassette.

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointed toward the VCR.

●Do not apply too much pressure when inserting.

●The VCR’s power comes on automatically.

●If the erase protection switch is set to “SAVE”, playback begins automatically. It takes about 15 seconds until the playback picture appears.

BSelect the DV deck.

Press DV.

●The DV button lights on the VCR.

CFind the program start point.

If the tape is advanced past the start point, press

REW (3) or turn the ADVANCED JOG dial to the left. To go forward, press FF (5) or turn the ADVANCED JOG dial to the right.

DStart playback.

Press PLAY (4).

●The DV playback indicator lights on the VCR.

EStop playback.

Press STOP (8). Then press EJECT () to remove the cassette.

●The DV playback indicator turns off.

Usable cassettes

Only cassettes marked	can be used with the DV
deck.

NOTE:

When you record a tape on the DV deck with the recording speed set to “LP”, it is recommended to play back the tape on this DV deck. Digital video recorder from other manufacturers may not be able to play back the tape properly.

Image 36

Contents Video Cassette Recorder For Customer UseDear Customer Moisture CondensationPower Sources Power Cord ProtectionPower Lines Grounding or PolarizationAccessories CleaningDamage Requiring Service Replacement PartsContents Front View Rear View Front Display Panel How To Use Remote10 EN ON-SCREEN Display for VHS deckTo recall an indication Press DISPLAY/OSDON-SCREEN Display for DV deck Check the contents Connect the VCR to power source12 EN Situate the VCR8To connect to a TV with S-VIDEO/AUDIO input connectors Video ConnectionPerform Plug & Play setup What to do if Plug & Play setting failedPlug & Play Set 14 ENLanguage Access the Clock Set screen Clock Set16 EN PreparationsSemiauto Clock Set Manual Clock SetAccess the Tuner Set screen Tuner Set18 EN Auto Channel SetAccess the Manual Channel Set screen Manual Channel SetAdd or skip the desired channels To add channelsInstalling Controller 20 ENAccess the Cable Box Set screen Turn on the cable boxSelect the cable box’s channel If you do not use a cable box, press rt until OFF22 EN Enter the cable box’s brandPress OK or e If the cable box’s channel does not change toIf your DBS receiver has audio/video output connectors How to control the DBS receiverDBS receiver DBS receiverSetting DBS receivers brand and channel Access the DBS Receiver Set screen24 EN Turn on the DBS receiverAccess the DBS Receiver Brand Set screen Enter the DBS receiver’s brandJVC Dish Network Echostar Dish Network Basic Playback 26 ENVHS deck Choose a program Set the tape speedStart recording Pause/Resume recording28 EN Slow Motion On the VCRActivate frame-by-frame playback Push the Advanced JOG dial Press PauseSlow Motion On the Remote Variable Speed Search On the RemoteForward 30 EN Index SearchRepeat Playback Next Function MemoryAdjust the tracking manually Manual TrackingSoundtrack Selection Override automatic trackingInstant Timer Recording ITR 32 ENRecord One Program While Watching Another Reset the counter Press C.RESET before starting recording or playbackElapsed Recording Time Indication Tape Remaining Time34 EN RetakeSecond Audio Recording Active Video Calibration PlaybackRecording 36 EN DV deckSelect the DV deck Press DVDV recording indicator lights on the VCR DV recording indicator turns off38 EN Step 40 EN Pressing A. Monitor changes the soundtrack as followsRight channel are mixed Sound on the right channel isTime Code Access the PlusCode No. screen Access the VCR Plus+ Program screen42 EN Select the deckEngage the VCR’s timer mode For the VHS deckFor the DV deck Cable Box or DBS Receiver UsersAccess the Guide Channel Set screen Cable Box Control Setting pg44 EN Guide Channel Number SetGuide Channel Number Enter the receiving channel position numberExpress Timer Programing 46 ENEnter the program date Enter the channel positionPress DATE+ Press CH+Enter the program mode 24HR Quick Programing48 EN Set the program start/stop time and channelPage To cancel or change a program 50 ENWhen programs overlap each other Cancel or change program settingConfirm the overlapping programs Select the program to modifyTape Dubbing 52 ENFrom DV to VHS Dubbing An Entire CassetteDubbing direction indicator S-VHS lights From VHS to DVPress DV, then press SP/LP p 54 EN Locate the start point on the DV deckPrepare the VHS deck for dubbing Pause dubbingVHS playback indicator and DV recording indicator light Locate the start point on the VHS deckPrepare the DV deck for dubbing Edit From a Camcorder 56 ENRecorder Video input PlayerSet the input mode of recording deck 58 ENStart the source player Start the recording deckConnection to a PC with DV connector Connection to another VCRAdvantages of S-VHS video recorders Audio Dubbing 60 ENVHS Audio Dubbing DV Audio DubbingEngage the Audio Dubbing mode End Audio DubbingPress A.DUB Insert Editing 62 ENVHS Insert Editing Source tape Recording tapeEngage the Insert Editing mode AV Insert Editing VHS deck onlyPrepare the recording cassette Start EditingAccess the R.A.Edit screen 64 ENProgram Editing Memory 8 programs x 8 scenes Select the programLocate the end point Prepare the source tapeStart Random Assemble Editing End Random Assemble EditingRemote A/B Code Switching Set the remote control code for RemoteCheck the remote control code for VCR 66 ENSet the TV brand code Operate the TVBefore performing the following steps TV CH +/-,TV VOL+/-, TV Muting, number keysPress the corresponding button Power 68 ENSet the Cable Box brand code Operate the Cable BoxTurn on the DBS receiver using its Remote Set the DBS receiver brand codeOperate the DBS receiver JVC Dish NetworkMode Set Access the Mode Set screenSelect the mode Select the mode settingWhen this function is set to on 72 EN Display panelVHS Mode SET While timer-recording in SP mode 74 ENFor Example Channel not in useCorrection to the luminance signal to enhance details Selecting either HI-FI L or HI-FI RNormally select this. Hi-Fi sound is played back Sound on the left Hi-Fi channel is played backEnables Audio Dubbing later 76 ENOriginal recorded sound Audio-dubbed soundIndicator off Remote won’t function Batteries are dischargedConsult your JVC dealer Message appears on the screen78 EN VHS deck DV deck80 EN Playback 82 EN Instant Timer Recording ITR Timer Warning DisplayGuide Channel Number Set Recording Resume FunctionHOW to Locate Your JVC Service Center 84 ENWarranty Only in U.S.A 86 EN

Related manuals

Manual 88 pages 31.07 Kb