JVC hr-dvs3u manual 24HR Quick Programing, 48 EN, Enter the program mode

Page 48

48 EN

TIMER RECORDING (cont.)

24HR Quick

Programing

Before performing the 24HR Quick Programing:

Make sure that the VCR’s built-in clock is set properly.

Select the deck.

Set the tape speed.

For the VHS deck:

Insert a VHS (or S-VHS) cassette with the record safety tab intact.

For the DV deck:

Insert a Mini DV cassette with the erase protection switch set to “REC”.

You can program a timer recording that starts within 24 hours using the ADVANCED JOG dial on the VCR.

AEnter the program mode.

Press 24HR QUICK PROGRAM on the VCR. The start time indicator ( ) starts blinking on the front display panel.

BSet the program start/stop time and channel.

Turn the ADVANCED JOG dial to the left or right to set the time you want recording to start.

One click stop of the ADVANCED JOG dial changes the time in 5-minute intervals.

1

3

2

Push the ADVANCED JOG dial. The stop time indicator

( ) starts blinking on the front display panel. Turn the ADVANCED JOG dial to the left or right to set the time you want recording to stop.

Push the ADVANCED JOG dial. Turn the ADVANCED JOG dial to the left or right to select the channel you wish to record.

You can cancel the setting at any time by pressing and holding the ADVANCED JOG dial for more than 3 seconds or pressing CANCEL on the Remote. Repeat the step 2.

CEngage the VCR’s timer mode.

Press 24HR QUICK PROGRAM. The VCR turns off automatically and “#” appears on the front display panel.

To disengage the timer mode, press TIMER or 24HR QUICK PROGRAM again.

Image 48
Contents Video Cassette Recorder For Customer UseDear Customer Moisture CondensationPower Sources Power Cord ProtectionPower Lines Grounding or PolarizationAccessories CleaningDamage Requiring Service Replacement PartsContents Front View Rear View Front Display Panel How To Use Remote10 EN ON-SCREEN Display for VHS deckTo recall an indication Press DISPLAY/OSDON-SCREEN Display for DV deck Check the contents Connect the VCR to power source12 EN Situate the VCR8To connect to a TV with S-VIDEO/AUDIO input connectors Video ConnectionPerform Plug & Play setup What to do if Plug & Play setting failedPlug & Play Set 14 ENLanguage Access the Clock Set screen Clock Set16 EN PreparationsSemiauto Clock Set Manual Clock SetAccess the Tuner Set screen Tuner Set18 EN Auto Channel SetAccess the Manual Channel Set screen Manual Channel SetAdd or skip the desired channels To add channelsInstalling Controller 20 ENAccess the Cable Box Set screen Turn on the cable boxSelect the cable box’s channel If you do not use a cable box, press rt until OFF22 EN Enter the cable box’s brandPress OK or e If the cable box’s channel does not change toIf your DBS receiver has audio/video output connectors How to control the DBS receiverDBS receiver DBS receiverSetting DBS receivers brand and channel Access the DBS Receiver Set screen24 EN Turn on the DBS receiverAccess the DBS Receiver Brand Set screen Enter the DBS receiver’s brandJVC Dish Network Echostar Dish Network Basic Playback 26 ENVHS deck Choose a program Set the tape speedStart recording Pause/Resume recording28 EN Slow Motion On the VCRActivate frame-by-frame playback Push the Advanced JOG dial Press PauseSlow Motion On the Remote Variable Speed Search On the RemoteForward 30 EN Index SearchRepeat Playback Next Function MemoryAdjust the tracking manually Manual TrackingSoundtrack Selection Override automatic trackingInstant Timer Recording ITR 32 ENRecord One Program While Watching Another Reset the counter Press C.RESET before starting recording or playbackElapsed Recording Time Indication Tape Remaining Time34 EN RetakeSecond Audio Recording Active Video Calibration PlaybackRecording 36 EN DV deckSelect the DV deck Press DVDV recording indicator lights on the VCR DV recording indicator turns off38 EN Step 40 EN Pressing A. Monitor changes the soundtrack as followsRight channel are mixed Sound on the right channel isTime Code Access the PlusCode No. screen Access the VCR Plus+ Program screen42 EN Select the deckEngage the VCR’s timer mode For the VHS deckFor the DV deck Cable Box or DBS Receiver UsersAccess the Guide Channel Set screen Cable Box Control Setting  pg44 EN Guide Channel Number SetGuide Channel Number Enter the receiving channel position numberExpress Timer Programing 46 ENEnter the program date Enter the channel positionPress DATE+ Press CH+Enter the program mode 24HR Quick Programing48 EN Set the program start/stop time and channelPage To cancel or change a program 50 ENWhen programs overlap each other Cancel or change program settingConfirm the overlapping programs Select the program to modifyTape Dubbing 52 ENFrom DV to VHS Dubbing An Entire CassetteDubbing direction indicator S-VHS lights From VHS to DVPress DV, then press SP/LP p 54 EN Locate the start point on the DV deckPrepare the VHS deck for dubbing Pause dubbingVHS playback indicator and DV recording indicator light Locate the start point on the VHS deckPrepare the DV deck for dubbing Edit From a Camcorder 56 ENRecorder Video input PlayerSet the input mode of recording deck 58 ENStart the source player Start the recording deckConnection to a PC with DV connector Connection to another VCRAdvantages of S-VHS video recorders Audio Dubbing 60 ENVHS Audio Dubbing DV Audio DubbingEngage the Audio Dubbing mode End Audio DubbingPress A.DUB Insert Editing 62 ENVHS Insert Editing Source tape Recording tapeEngage the Insert Editing mode AV Insert Editing VHS deck onlyPrepare the recording cassette Start EditingAccess the R.A.Edit screen 64 ENProgram Editing Memory 8 programs x 8 scenes Select the programLocate the end point Prepare the source tapeStart Random Assemble Editing End Random Assemble EditingRemote A/B Code Switching Set the remote control code for RemoteCheck the remote control code for VCR 66 ENSet the TV brand code Operate the TVBefore performing the following steps TV CH +/-,TV VOL+/-, TV Muting, number keysPress the corresponding button Power 68 ENSet the Cable Box brand code Operate the Cable BoxTurn on the DBS receiver using its Remote Set the DBS receiver brand codeOperate the DBS receiver JVC Dish NetworkMode Set Access the Mode Set screenSelect the mode Select the mode settingWhen this function is set to on 72 EN Display panelVHS Mode SET While timer-recording in SP mode 74 ENFor Example Channel not in useCorrection to the luminance signal to enhance details Selecting either HI-FI L or HI-FI RNormally select this. Hi-Fi sound is played back Sound on the left Hi-Fi channel is played backEnables Audio Dubbing later 76 ENOriginal recorded sound Audio-dubbed soundIndicator off Remote won’t function Batteries are dischargedConsult your JVC dealer Message appears on the screen78 EN VHS deck DV deck80 EN Playback 82 EN Instant Timer Recording ITR Timer Warning DisplayGuide Channel Number Set Recording Resume FunctionHOW to Locate Your JVC Service Center 84 ENWarranty Only in U.S.A 86 EN
Related manuals
Manual 88 pages 31.07 Kb