JVC hr-dvs3u manual VHS Mode SET

Page 73

EN 73

VHS MODE SET (cont.)

* The default setting is bold in the table below.

8VIDEO CALIBRATION When this function is set to “ON”, this VCR checks the condition of the tape in use

ON	during playback and recording, and compensates to provide the highest-possible
OFF	pictures. This takes place whenever you play back a tape or start recording after
	inserting a tape. ( pg. 35)

8 PICTURE CONTROL	This feature helps you to adjust the playback picture quality according to your
AUTO	preference. Normally select “AUTO”.
EDIT	AUTO:	Provides the optimized picture benefits of the VIDEO
SOFT		CALIBRATION Picture System.
SHARP	EDIT:	Minimizes picture degradation during editing (recording and
	SOFT:	playback).
	SOFT:	Reduces image coarseness when viewing overplayed tapes
	SHARP:	containing a lot of noise.
	SHARP:	Clearer, sharper-edged picture when viewing images with lots of
		flat, same-coloured surfaces such as cartoons.
	NOTES:
	● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not change until you
	select another mode.
	● When you select “EDIT” to dub tapes, be sure to select “AUTO” after you finish dubbing
	the tapes.
	● When “VIDEO CALIBRATION” is “OFF”, “PICTURE CONTROL” switches automatically
	from “AUTO” to “NORM”.

8 FRONT AUX INPUT	Select the appropriate mode depending on the connector being used on the front
VIDEO	panel.
S-VIDEO	VIDEO:	To use the VIDEO input connector on the front panel.
	S-VIDEO:	To use the S-VIDEO input connector on the front panel.

Image 73

Contents For Customer Use Video Cassette RecorderMoisture Condensation Dear CustomerPower Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Front View Rear View Front Display Panel Remote How To UseON-SCREEN Display for VHS deck 10 ENTo recall an indication Press DISPLAY/OSDON-SCREEN Display for DV deck Connect the VCR to power source Check the contents12 EN Situate the VCRVideo Connection 8To connect to a TV with S-VIDEO/AUDIO input connectorsWhat to do if Plug & Play setting failed Perform Plug & Play setupPlug & Play Set 14 ENLanguage Clock Set Access the Clock Set screen16 EN PreparationsManual Clock Set Semiauto Clock SetTuner Set Access the Tuner Set screen18 EN Auto Channel SetManual Channel Set Access the Manual Channel Set screenAdd or skip the desired channels To add channels20 EN Installing ControllerTurn on the cable box Access the Cable Box Set screenSelect the cable box’s channel If you do not use a cable box, press rt until OFFEnter the cable box’s brand 22 ENPress OK or e If the cable box’s channel does not change toHow to control the DBS receiver If your DBS receiver has audio/video output connectorsDBS receiver DBS receiverAccess the DBS Receiver Set screen Setting DBS receivers brand and channel24 EN Turn on the DBS receiverEnter the DBS receiver’s brand Access the DBS Receiver Brand Set screenJVC Dish Network Echostar Dish Network 26 EN Basic PlaybackVHS deck Set the tape speed Choose a programStart recording Pause/Resume recordingSlow Motion On the VCR 28 ENActivate frame-by-frame playback Push the Advanced JOG dial Press PauseVariable Speed Search On the Remote Slow Motion On the RemoteForward Index Search 30 ENRepeat Playback Next Function MemoryManual Tracking Adjust the tracking manuallySoundtrack Selection Override automatic tracking32 EN Instant Timer Recording ITRRecord One Program While Watching Another Press C.RESET before starting recording or playback Reset the counterElapsed Recording Time Indication Tape Remaining TimeRetake 34 ENSecond Audio Recording Playback Active Video CalibrationRecording DV deck 36 ENSelect the DV deck Press DVDV recording indicator turns off DV recording indicator lights on the VCR38 EN Step Pressing A. Monitor changes the soundtrack as follows 40 ENRight channel are mixed Sound on the right channel isTime Code Access the VCR Plus+ Program screen Access the PlusCode No. screen42 EN Select the deckFor the VHS deck Engage the VCR’s timer modeFor the DV deck Cable Box or DBS Receiver UsersCable Box Control Setting pg Access the Guide Channel Set screen44 EN Guide Channel Number SetEnter the receiving channel position number Guide Channel Number46 EN Express Timer ProgramingEnter the channel position Enter the program datePress DATE+ Press CH+24HR Quick Programing Enter the program mode48 EN Set the program start/stop time and channelPage 50 EN To cancel or change a programCancel or change program setting When programs overlap each otherConfirm the overlapping programs Select the program to modify52 EN Tape DubbingFrom DV to VHS Dubbing An Entire CassetteFrom VHS to DV Dubbing direction indicator S-VHS lightsPress DV, then press SP/LP p Locate the start point on the DV deck 54 ENPrepare the VHS deck for dubbing Pause dubbingLocate the start point on the VHS deck VHS playback indicator and DV recording indicator lightPrepare the DV deck for dubbing 56 EN Edit From a CamcorderPlayer Recorder Video input58 EN Set the input mode of recording deckStart the source player Start the recording deckConnection to another VCR Connection to a PC with DV connectorAdvantages of S-VHS video recorders 60 EN Audio DubbingVHS Audio Dubbing DV Audio DubbingEnd Audio Dubbing Engage the Audio Dubbing modePress A.DUB 62 EN Insert EditingVHS Insert Editing Source tape Recording tapeAV Insert Editing VHS deck only Engage the Insert Editing modePrepare the recording cassette Start Editing64 EN Access the R.A.Edit screenProgram Editing Memory 8 programs x 8 scenes Select the programPrepare the source tape Locate the end pointStart Random Assemble Editing End Random Assemble EditingSet the remote control code for Remote Remote A/B Code SwitchingCheck the remote control code for VCR 66 ENOperate the TV Set the TV brand codeBefore performing the following steps TV CH +/-,TV VOL+/-, TV Muting, number keys68 EN Press the corresponding button PowerSet the Cable Box brand code Operate the Cable BoxSet the DBS receiver brand code Turn on the DBS receiver using its RemoteOperate the DBS receiver JVC Dish NetworkAccess the Mode Set screen Mode SetSelect the mode Select the mode settingWhen this function is set to on Display panel 72 ENVHS Mode SET 74 EN While timer-recording in SP modeFor Example Channel not in useSelecting either HI-FI L or HI-FI R Correction to the luminance signal to enhance detailsNormally select this. Hi-Fi sound is played back Sound on the left Hi-Fi channel is played back76 EN Enables Audio Dubbing laterOriginal recorded sound Audio-dubbed soundRemote won’t function Batteries are discharged Indicator offConsult your JVC dealer Message appears on the screen78 EN DV deck VHS deck80 EN Playback 82 EN Timer Warning Display Instant Timer Recording ITRGuide Channel Number Set Recording Resume Function84 EN HOW to Locate Your JVC Service CenterWarranty Only in U.S.A 86 EN

Related manuals

Manual 88 pages 31.07 Kb