JVC hr-dvs3u manual AV Insert Editing VHS deck only, Prepare the recording cassette, Start Editing

Page 63

EN 63

AMake connections.

Connect the player’s VIDEO OUT or S-VIDEO OUT and AUDIO OUT connectors to your VCR’s VIDEO or S-VIDEO and AUDIO input connectors.

BSet the VCR’s input mode.

Press AUX (number key “0”) and/or CH +/– to select “F-1” (or “L-1” if you use the connectors on the rear).

●When using S VIDEO connector, set “FRONT AUX INPUT” (or

“REAR AUX INPUT” if you use the connectors on the rear) to “S-VIDEO”. ( pg. 71, 73)

●When using VIDEO connector, set “FRONT AUX INPUT” (or “REAR AUX INPUT”) to “VIDEO”. ( pg. 71, 73)

CSelect the recording deck.

Press S-VHSor DV.

●When using the DV deck as the recording deck, press so that the video and audio signals from the VIDEO/S-VIDEO and AUDIO L + R input connectors can be recorded. The dubbing direction indicator ( S-VHS) lights.

DPrepare the recording cassette.

For the VHS deck

Load the recording cassette into the VHS deck, and play it back to determine the edit-out point (the end of the segment to be replaced) using the ADVANCED JOG dial, or pressing w e and PAUSE (9).

Then press C.RESET to reset the counter.

For the DV deck

Load the recording cassette into the DV deck.

ELocate the start point.

Determine the edit-in point (the beginning of the segment to be replaced) using the ADVANCED JOG dial, or pressing w e and PAUSE (9).

●Be sure to engage the Still mode at the edit-in point.

FEngage the Insert Editing mode.

Press INSERT.

●Your VCR enters the Insert Pause mode. (“o”, “u” and “i” light up on the front display panel.)

●The TV screen changes from the still picture to the input source you are going to record.

GStart Editing.

Load the source cassette and play back the segment that is to be inserted. When you reach the start of the section of the source tape that you wish to insert, press PLAY (4) to start the tape in your VCR; Insert Editing begins at this point.

●“o” and “u” are displayed on the front display panel.

HEnd Insert Editing.

For the VHS deck

At counter “0:00:00”, Insert Editing will stop automatically while the tape continues running in the Play mode. If you wish to stop Insert Editing before the specified edit-out point, press C.RESET.

For the DV deck

Press STOP (8) to stop recording on the DV deck.

AV Insert Editing (VHS deck only)

If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time ...

... In step 6, after you press INSERT, press A.DUB also. (“o” and “u” blink and “i” lights up on the front display panel.)

NOTES:

●Once the Insert Editing starts, you can not use the other deck.

●All necessary cables can be obtained from your dealer.

●Insert Editing cannot be performed on a VHS (or S-VHS) cassette that has had its record safety tab removed, or on a Mini DV cassette that has had its erase protection switch set to “SAVE”.

●When Insert Editing is performed on a tape that has been recorded on another VCR, the inserted portion may appear distorted.

●In Insert Editing, the recording speed (SP/EP) is determined by the previous recording to be replaced. If the previous recording’s speed changes within a single edit, the inserted picture will be distorted at the switching point. (VHS deck only)

●A small portion of the recording which precedes an insert edit may become erased.

●Insert Editing is also possible using the rear panel connectors.

When using these connectors, be sure to set “REAR AUX INPUT” to the appropriate mode. ( pg. 71)

●Insert Editing is not possible using the DV IN/OUT connector.

●Insert Editing is not possible on a blank portion of the tape.

Page 62 Page 64
Image 63
Page 62 Page 64
Contents For Customer Use Video Cassette RecorderMoisture Condensation Dear CustomerGrounding or Polarization Power SourcesPower Cord Protection Power LinesReplacement Parts AccessoriesCleaning Damage Requiring ServiceContents Front View Rear View Front Display Panel Remote How To UsePress DISPLAY/OSD 10 ENON-SCREEN Display for VHS deck To recall an indicationON-SCREEN Display for DV deck Situate the VCR Check the contentsConnect the VCR to power source 12 ENVideo Connection 8To connect to a TV with S-VIDEO/AUDIO input connectors14 EN Perform Plug & Play setupWhat to do if Plug & Play setting failed Plug & Play SetLanguage Preparations Access the Clock Set screenClock Set 16 ENManual Clock Set Semiauto Clock SetAuto Channel Set Access the Tuner Set screenTuner Set 18 ENTo add channels Access the Manual Channel Set screenManual Channel Set Add or skip the desired channels20 EN Installing ControllerIf you do not use a cable box, press rt until OFF Access the Cable Box Set screenTurn on the cable box Select the cable box’s channelIf the cable box’s channel does not change to 22 ENEnter the cable box’s brand Press OK or eDBS receiver If your DBS receiver has audio/video output connectorsHow to control the DBS receiver DBS receiverTurn on the DBS receiver Setting DBS receivers brand and channelAccess the DBS Receiver Set screen 24 ENAccess the DBS Receiver Brand Set screen Enter the DBS receiver’s brandJVC Dish Network Echostar Dish Network Basic Playback 26 ENVHS deck Pause/Resume recording Choose a programSet the tape speed Start recordingPush the Advanced JOG dial Press Pause 28 ENSlow Motion On the VCR Activate frame-by-frame playbackSlow Motion On the Remote Variable Speed Search On the RemoteForward Next Function Memory 30 ENIndex Search Repeat PlaybackOverride automatic tracking Adjust the tracking manuallyManual Tracking Soundtrack SelectionInstant Timer Recording ITR 32 ENRecord One Program While Watching Another Tape Remaining Time Reset the counterPress C.RESET before starting recording or playback Elapsed Recording Time Indication34 EN RetakeSecond Audio Recording Active Video Calibration PlaybackRecording Press DV 36 ENDV deck Select the DV deckDV recording indicator turns off DV recording indicator lights on the VCR38 EN Step Sound on the right channel is 40 ENPressing A. Monitor changes the soundtrack as follows Right channel are mixedTime Code Select the deck Access the PlusCode No. screenAccess the VCR Plus+ Program screen 42 ENCable Box or DBS Receiver Users Engage the VCR’s timer modeFor the VHS deck For the DV deckGuide Channel Number Set Access the Guide Channel Set screenCable Box Control Setting  pg 44 ENEnter the receiving channel position number Guide Channel Number46 EN Express Timer ProgramingPress CH+ Enter the program dateEnter the channel position Press DATE+Set the program start/stop time and channel Enter the program mode24HR Quick Programing 48 ENPage 50 EN To cancel or change a programSelect the program to modify When programs overlap each otherCancel or change program setting Confirm the overlapping programsDubbing An Entire Cassette Tape Dubbing52 EN From DV to VHSDubbing direction indicator S-VHS lights From VHS to DVPress DV, then press SP/LP p Pause dubbing 54 ENLocate the start point on the DV deck Prepare the VHS deck for dubbingVHS playback indicator and DV recording indicator light Locate the start point on the VHS deckPrepare the DV deck for dubbing 56 EN Edit From a CamcorderPlayer Recorder Video inputStart the recording deck Set the input mode of recording deck58 EN Start the source playerConnection to a PC with DV connector Connection to another VCRAdvantages of S-VHS video recorders DV Audio Dubbing Audio Dubbing60 EN VHS Audio DubbingEngage the Audio Dubbing mode End Audio DubbingPress A.DUB Source tape Recording tape Insert Editing62 EN VHS Insert EditingStart Editing Engage the Insert Editing modeAV Insert Editing VHS deck only Prepare the recording cassetteSelect the program Access the R.A.Edit screen64 EN Program Editing Memory 8 programs x 8 scenesEnd Random Assemble Editing Locate the end pointPrepare the source tape Start Random Assemble Editing66 EN Remote A/B Code SwitchingSet the remote control code for Remote Check the remote control code for VCRTV CH +/-,TV VOL+/-, TV Muting, number keys Set the TV brand codeOperate the TV Before performing the following stepsOperate the Cable Box Press the corresponding button Power68 EN Set the Cable Box brand codeJVC Dish Network Turn on the DBS receiver using its RemoteSet the DBS receiver brand code Operate the DBS receiverSelect the mode setting Mode SetAccess the Mode Set screen Select the modeWhen this function is set to on Display panel 72 ENVHS Mode SET Channel not in use While timer-recording in SP mode74 EN For ExampleSound on the left Hi-Fi channel is played back Correction to the luminance signal to enhance detailsSelecting either HI-FI L or HI-FI R Normally select this. Hi-Fi sound is played backAudio-dubbed sound Enables Audio Dubbing later76 EN Original recorded soundMessage appears on the screen Indicator offRemote won’t function Batteries are discharged Consult your JVC dealer78 EN DV deck VHS deck80 EN Playback 82 EN Recording Resume Function Instant Timer Recording ITRTimer Warning Display Guide Channel Number Set84 EN HOW to Locate Your JVC Service CenterWarranty Only in U.S.A 86 EN
Related manuals
Manual 88 pages 31.07 Kb
Top Page Image Contents