JVC hr-dvs3u manual 66 EN, Remote A/B Code Switching, Set the remote control code for Remote

Page 66

66 EN

REMOTE CONTROL FUNCTIONS

Remote A/B Code Switching

This Remote is capable of transmitting two control codes; one set to respond to A code control signals and another set to respond to B code control signals. This Remote control is preset to send A code signals because your VCR is initially set to respond to A code signals. You can easily modify your VCR and the Remote to respond to B code signals. When using two JVC VCRs, set two VCRs and their Remotes to different codes, so that you can operate these VCRs separately.

1

3

2

ASet the remote control code for Remote.

APress and hold A/B.

BPress the number key “2”.

CPress STOP (8), and release A/B.

●The Remote now can transmit B code control signals.

BCheck the remote control code for VCR.

Press and hold PLAY (4) on the VCR for more than

5 seconds while the VCR is turned off. The code currently set appears on the display panel.

CChange the code for VCR.

Press any key on the Remote. The VCR now responds to B code control signals.

●To set the Remote and the VCR back to A code control signals, repeat the same procedure as shown above except pressing the number key “1” in step B of 1.

T

1

4

7

1

To control two VCRs with the same Remote

You can control two JVC VCRs by switching the remote control code for the Remote between A and B ( step 1), keeping two VCRs to different control codes.

●To change only the remote control code for the Remote, DO NOT perform steps 2 and 3.

W

23

2

56

89

04

DV S-VHS

Image 66

Contents Video Cassette Recorder For Customer UseDear Customer Moisture CondensationPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents Front View Rear View Front Display Panel How To Use RemoteTo recall an indication 10 ENON-SCREEN Display for VHS deck Press DISPLAY/OSDON-SCREEN Display for DV deck 12 EN Check the contentsConnect the VCR to power source Situate the VCR8To connect to a TV with S-VIDEO/AUDIO input connectors Video ConnectionPlug & Play Set Perform Plug & Play setupWhat to do if Plug & Play setting failed 14 ENLanguage 16 EN Access the Clock Set screenClock Set PreparationsSemiauto Clock Set Manual Clock Set18 EN Access the Tuner Set screenTuner Set Auto Channel SetAdd or skip the desired channels Access the Manual Channel Set screenManual Channel Set To add channelsInstalling Controller 20 ENSelect the cable box’s channel Access the Cable Box Set screenTurn on the cable box If you do not use a cable box, press rt until OFFPress OK or e 22 ENEnter the cable box’s brand If the cable box’s channel does not change toDBS receiver If your DBS receiver has audio/video output connectorsHow to control the DBS receiver DBS receiver24 EN Setting DBS receivers brand and channelAccess the DBS Receiver Set screen Turn on the DBS receiverAccess the DBS Receiver Brand Set screen Enter the DBS receiver’s brandJVC Dish Network Echostar Dish Network Basic Playback 26 ENVHS deck Start recording Choose a programSet the tape speed Pause/Resume recordingActivate frame-by-frame playback 28 ENSlow Motion On the VCR Push the Advanced JOG dial Press PauseSlow Motion On the Remote Variable Speed Search On the RemoteForward Repeat Playback 30 ENIndex Search Next Function MemorySoundtrack Selection Adjust the tracking manuallyManual Tracking Override automatic trackingInstant Timer Recording ITR 32 ENRecord One Program While Watching Another Elapsed Recording Time Indication Reset the counterPress C.RESET before starting recording or playback Tape Remaining Time34 EN RetakeSecond Audio Recording Active Video Calibration PlaybackRecording Select the DV deck 36 ENDV deck Press DVDV recording indicator lights on the VCR DV recording indicator turns off38 EN Step Right channel are mixed 40 ENPressing A. Monitor changes the soundtrack as follows Sound on the right channel isTime Code 42 EN Access the PlusCode No. screenAccess the VCR Plus+ Program screen Select the deckFor the DV deck Engage the VCR’s timer modeFor the VHS deck Cable Box or DBS Receiver Users44 EN Access the Guide Channel Set screenCable Box Control Setting pg Guide Channel Number SetGuide Channel Number Enter the receiving channel position numberExpress Timer Programing 46 ENPress DATE+ Enter the program dateEnter the channel position Press CH+48 EN Enter the program mode24HR Quick Programing Set the program start/stop time and channelPage To cancel or change a program 50 ENConfirm the overlapping programs When programs overlap each otherCancel or change program setting Select the program to modifyFrom DV to VHS Tape Dubbing52 EN Dubbing An Entire CassetteDubbing direction indicator S-VHS lights From VHS to DVPress DV, then press SP/LP p Prepare the VHS deck for dubbing 54 ENLocate the start point on the DV deck Pause dubbingVHS playback indicator and DV recording indicator light Locate the start point on the VHS deckPrepare the DV deck for dubbing Edit From a Camcorder 56 ENRecorder Video input PlayerStart the source player Set the input mode of recording deck58 EN Start the recording deckConnection to a PC with DV connector Connection to another VCRAdvantages of S-VHS video recorders VHS Audio Dubbing Audio Dubbing60 EN DV Audio DubbingEngage the Audio Dubbing mode End Audio DubbingPress A.DUB VHS Insert Editing Insert Editing62 EN Source tape Recording tapePrepare the recording cassette Engage the Insert Editing modeAV Insert Editing VHS deck only Start EditingProgram Editing Memory 8 programs x 8 scenes Access the R.A.Edit screen64 EN Select the programStart Random Assemble Editing Locate the end pointPrepare the source tape End Random Assemble EditingCheck the remote control code for VCR Remote A/B Code SwitchingSet the remote control code for Remote 66 ENBefore performing the following steps Set the TV brand codeOperate the TV TV CH +/-,TV VOL+/-, TV Muting, number keysSet the Cable Box brand code Press the corresponding button Power68 EN Operate the Cable BoxOperate the DBS receiver Turn on the DBS receiver using its RemoteSet the DBS receiver brand code JVC Dish NetworkSelect the mode Mode SetAccess the Mode Set screen Select the mode settingWhen this function is set to on 72 EN Display panelVHS Mode SET For Example While timer-recording in SP mode74 EN Channel not in useNormally select this. Hi-Fi sound is played back Correction to the luminance signal to enhance detailsSelecting either HI-FI L or HI-FI R Sound on the left Hi-Fi channel is played backOriginal recorded sound Enables Audio Dubbing later76 EN Audio-dubbed soundConsult your JVC dealer Indicator offRemote won’t function Batteries are discharged Message appears on the screen78 EN VHS deck DV deck80 EN Playback 82 EN Guide Channel Number Set Instant Timer Recording ITRTimer Warning Display Recording Resume FunctionHOW to Locate Your JVC Service Center 84 ENWarranty Only in U.S.A 86 EN

Related manuals

Manual 88 pages 31.07 Kb