JVC HR-DD865EK setup guide Safety Precautions, Do not place the recorder

Page 2

2

SAFETYFIRST

Safety Precautions

The rating plate and the safety caution are on the rear of the unit.

WARNING: DANGEROUS VOLTAGE INSIDE

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

IMPORTANT

Please read the various precautions on p. 2 – 3 of this instruction manual before installing or operating the recorder.

It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video record- ing, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.

IMPORTANT

Connection to the mains supply in the United Kingdom. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain a proper safety approved extension lead/adapter or consult your dealer.

In the unlikely event of the plug fuse failing be sure to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover. If the fuse fails again consult your nearest JVC dealer.

If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If this product is not supplied fitted with a mains plug then follow the instructions given below:

DO NOT make any connection to the Larger Terminal coded E or Green.

The wires in the mains lead are coloured in accordance with the following code:

Blue to N (Neutral) or Black

Brown to L (Live) or Red

If these colours do not correspond with the terminal identifications of your plug, connect as follows:

Blue wire to terminal coded N (Neutral) or coloured Black. Brown wire to terminal coded L (Live) or coloured Red.

If in doubt — consult a competent electrician.

PAL

Cassettes marked "VHS" (or "S-VHS") can be used with this video recorder. However, only VHS recordings can be made and played back.

HQ VHS is compatible with existing VHS equipment.

VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO Plus+ system is manufactured under license from Gemstar Development Corporation.

CAUTION

When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet.

Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.

The STANDBY/ON button does not completely shut off mains power from the unit, but switches operating

current on and off. " " shows electrical power standby and " " shows ON.

Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a single-speed video recorder.

Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette.

1. DO NOT place the recorder . . .

... in an environment prone to extreme temperatures or humidity.

... in direct sunlight.

... in a dusty environment.

... in an environment where strong magnetic fields are generated.

... on a surface that is unstable or subject to vibration.

2.DO NOT block the recorder’s ventilation openings.

3.DO NOT place heavy objects on the recorder or remote control.

4.DO NOT place anything which might spill on top of the recorder or remote control.

5.AVOID violent shocks to the recorder during transport.

MOISTURE CONDENSATION

Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.

ABOUT HEAD CLEANING

Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or inter- rupted. Be sure to contact your nearest JVC dealer if such troubles occur.

Image 2
Contents HR-DD865EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV To connect to a TV with 21-pin AV input connector ScartAV input connector Scart TV Aerial Cable not providedBeginningEnd If you have connected the video recorder toYour TV via both an RF cable and a 21-pin Go to item8 or If -- appears on the display panel, refer Remote control while downloading isPress OK to exit Video Channel Set mode Link screen will appear. Then the GuideIf auto channel set has succeeded but auto clock set has not Turn on the Recorder TV Auto Power OnLink Functions NexTView LinkPoint PlaybackLoad a Cassette Start PlaybackSlow Motion Activate HIGH-SPEED SearchStill Picture/Frame-By-Frame Playback High-Speed Turbo SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Access Mode SET Screen Adjust TrackingAccess Main Menu Screen SET ModePlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemOr press Record on the recorder RecordingPlayback Skip Over Unwanted Looking For Scene You WantActivate Index Search SectionsInstant ReView Activate InstantReview Normal recorder TimeScanVariable-Speed Search/ Reverse Play VisibleNoiselessMove the highlight bar pointer to Time Scan Audio TimeScanSpeed SP Speed LP Audio output Control Screen Access Main MenuSelecting Sound You Want Hi-Fi Audio Recording Level ControlType of Broadcast On-screen Display Being Received Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Satellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording AerialPressing %Þ, then press OK or # Move the highlight bar pointer to Mode SET byBefore performing the following steps Move the highlight bar pointer to AV2 SELECT, byRemote A/B Code Switching SET Remote ControlRE-SUPPLY Power Remote Con- trol FunctionsSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Operate TVTV Prog +/-,NUMBER keys Satellite Receiver Multi- Brand Remote ControlOperate Satellite Receiver Edit From Camcorder Repeat steps 4 6 as necessary ConnectorSynchro Editing SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Start Source PlayerAV2 Select Setting Engage Audio Dubbing SET Input ModeLocate Start Point Start DubbingLocate END Point Reset the CounterInsert Editing END Insert Editing Engage Insert EditingStart Editing Terminal Terminal JLIPJoint Level Interface Protocol ConnectorInformation On J Terminal Press OK orOther Functions Access Mode SETENABLE/DISABLE ON-SCREEN DisplayPower Save Mode Power SAVE, then pressNext Function Memory Auto SP→LP TimerAuto Timer Repeat Playback Engage RECORD-PAUSE ModeResume Recording RetakeConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionAuto Channel Set Tuner SetPerform Auto Channel SET Is displayed on the screen Screen preset positionsAfter Scan Completed For about 5 seconds, aStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Channel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Channel IslandsClock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Questions And Answers PlaybackTroubleshooting Timer Recording Won’t stopIndex Front ViewRear View Remote Control Remote Control LCD How To UseVHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical