JVC HR-DD865EK setup guide Questions And Answers, Playback

Page 57

SUBSIDIARYINFORMATION

57

Questions And Answers

PLAYBACK

Q. What happens if the end of the tape is reached during playback or search?

A. The tape is automatically rewound to the beginning.

Q. Can the video recorder indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this?

A.No, it is normal.

Q.Sometimes, during Index Search, the video recorder can’t find the programme I want to see. Why not?

A.There may be index codes too close together.

TIMER RECORDING

Q. "" and "ä" remain lit on the display panel. Is there

aproblem?

A.No. This is a normal condition for a timer recording in progress.

Q.Can I programme the timer while I’m watching a tape or a TV broadcast?

A.You won’t see the picture as it is replaced by the on- screen menu, but the audio from the program or tape you’re viewing can be heard.

Q.Is it possible to timer-record a TV programme broadcast in 2000?

A.Yes, it is possible.

RECORDING

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?

A. This is normal. It reduces distortion at the pause and resume points.

Q. Can the video recorder indefinitely remain in the Record-Pause mode?

A. No. The video recorder shuts off automatically after 5 minutes to protect the heads.

Q. What happens if the tape runs out during recording? A. The video recorder automatically rewinds it to the

beginning or, if Timer Recording, the cassette is ejected.

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 57
Contents HR-DD865EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide AV input connector Scart To connect to a TV with 21-pin AV input connector ScartBack of TV TV Aerial Cable not providedYour TV via both an RF cable and a 21-pin If you have connected the video recorder toBeginningEnd Go to itemPress OK to exit Video Channel Set mode Remote control while downloading is8 or If -- appears on the display panel, refer Link screen will appear. Then the GuideIf auto channel set has succeeded but auto clock set has not Link Functions TV Auto Power OnTurn on the Recorder NexTView LinkLoad a Cassette PlaybackPoint Start PlaybackStill Picture/Frame-By-Frame Playback Activate HIGH-SPEED SearchSlow Motion High-Speed Turbo SearchRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Access Main Menu Screen Adjust TrackingAccess Mode SET Screen SET ModeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsRecording PlaybackOr press Record on the recorder Activate Index Search Looking For Scene You WantSkip Over Unwanted SectionsActivate Instant ReviewInstant ReView Variable-Speed Search/ Reverse Play TimeScanNormal recorder VisibleNoiselessTimeScan Speed SP Speed LP Audio outputMove the highlight bar pointer to Time Scan Audio Selecting Sound You Want Access Main MenuControl Screen Hi-Fi Audio Recording Level ControlReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionType of Broadcast On-screen Display Being Received Automatic Satellite Programme Recording Aerial connectorSatellite Receiver Unit AerialBefore performing the following steps Move the highlight bar pointer to Mode SET byPressing %Þ, then press OK or # Move the highlight bar pointer to AV2 SELECT, byRE-SUPPLY Power SET Remote ControlRemote A/B Code Switching Remote Con- trol FunctionsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVSatellite Receiver Multi- Brand Remote Control Operate Satellite ReceiverTV Prog +/-,NUMBER keys Edit From Camcorder Connector Synchro EditingRepeat steps 4 6 as necessary Edit To Or From Another Video Recorder Input ModeSET Recording DECK’S Start Source PlayerAV2 Select Setting Locate Start Point SET Input ModeEngage Audio Dubbing Start DubbingReset the Counter Insert EditingLocate END Point Engage Insert Editing Start EditingEND Insert Editing Information On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorTerminal Press OK orENABLE/DISABLE Access Mode SETOther Functions ON-SCREEN DisplayPower SAVE, then press Power Save ModeAuto SP→LP Timer Auto TimerNext Function Memory Resume Recording Engage RECORD-PAUSE ModeRepeat Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalTuner Set Perform Auto Channel SETAuto Channel Set After Scan Completed Screen preset positionsIs displayed on the screen For about 5 seconds, aStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Switch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List Channel Islands TV Station Channel Number GuideJust Clock Clock SetVideo Plus+ Setup NumberGuide Program Number Set Playback Questions And AnswersTroubleshooting Won’t stop Timer RecordingFront View IndexRear View Remote Control How To Use Remote Control LCDMaximum recording time DA4 Double Azimuth helicalVHF 44.5 143/143 470 MHz